Stucco house: Advantages and Disadvantages of Stucco Homes

2022 Cost To Stucco A House

Stucco Siding Installation Cost

The average cost to install stucco siding on a house is $8,500 to $12,100 with most homeowners spending $9,300 for materials and labor. Stucco installation costs $3 to $9 per square foot depending on if its a new install, re-stucco, or applying stucco over an existing surface.

Stucco Cost

National Average Cost	$9,288
Minimum Cost	$4,500
Maximum Cost	$15,000
Average Range	$8,576 to $12,148

Stucco is a high-end siding material that costs 60% more installed than vinyl or aluminum siding, but the long-term stucco cost can end up cheaper because of its durability. Stucco is composed of natural materials and can last for decades if it’s well looked after; and modern-day stucco is of even better quality than previous decades because of the addition of epoxy, which causes the stucco to be less likely to crack or chip.

Table of Contents

1. Stucco Siding Installation Cost
2. Cost to Stucco a House

• Cost Per Square Foot
• Materials Cost
• Labor Cost
• Cost Factors

Stucco Siding Cost Estimator

• Stucco Over Brick
• Exterior Wall Cost
• Stucco vs. Siding
• Stucco vs. Brick

Cost to Re-Stucco a House

• Stucco Removal
• Stucco Resurfacing
• Stucco Repair

Pros and Cons of Stucco

• Tips for Maintaining Stucco

Types of Stucco Finishes

Frequently Asked Questions

DIY Stucco Vs. Hiring a Pro

Stucco Contractors Near Me

Cost to Stucco a House

The average cost to stucco a house is $7 to $9 per square foot with most homeowners spending $8. Stucco siding installation on an average home costs $8,000 to $12,000 for materials and labor. To re-stucco a house, add $1 per square foot for stucco removal costs.

Cost To Stucco A House

House Size	Average Cost
1,500 SF (1,239 SF of Siding)	$7,400 – $11,200
2,000 SF (1,431 SF of Siding)	$8,600 – $12,900
2,500 SF (1,575 SF of Siding)	$9,400 – $14,200
3,000 SF (1,753 SF of Siding)	$10,300 – $15,800

Stucco installation costs about $7,500 for a small house, $11,000 for a medium-sized house, and $14,000 for a large house. Applied as a textured or smooth look, stucco should be installed by a professional to ensure correct coverage and a specialized finish.

Stucco Cost Per Square Foot

Stucco costs $3 to $9 per square foot installed with most spending $8 per square foot on average. Applying stucco over bricks will cost as little as $3 per sqft., whereas a new application can cost $9 per sqft..

Stucco Cost Per Square Foot

Item	Cost Per Square Foot
Materials	$5 – $6
Labor	$2 – $3
Equipment	$0.30 – $0.50
Average Total	$7 – $9

Stucco Materials Cost

Stucco materials cost between $5 and $6 per square foot, which includes acrylic or cement stucco, weather wrapping, wire mesh, and coloring. Exterior stucco prices range from $0.05 to $0.50 per square foot with acrylic costing about five times more than cement.

Stucco Prices

Stucco Type	Cost Per Square Foot
Cement Stucco	$0. 05 – $0.10
Acrylic Stucco	$0.25 – $0.50
Stucco Mesh	$0.63 – $0.81

This cost is factored for mid-grade materials and covers the three layers of stucco necessary to give the wall the correct finish. The first coat is the scratch cost, the second coat is the levelling coat or brown coat, and the last is the finishing coat. The type of stucco you opt for (traditional or synthetic) and the finished texture will change the pricing as well.

Acrylic Vs Cement Stucco

Type	Pros	Cons
Acrylic ($40 to $60/5-gallons and covers 100–250 square feet.)	More flexible, so fewer hairline cracks Usually applied in a sand finish texture Available in multiple color options No need for a mixer	Shouldn’t be applied in temps lower than 40°F Water repellent but can soften over time in high-moisture areas Dries quickly, which can make an application more difficult
Cement (Costs $10–$15/90-lb. bag and covers 100–180 square feet.)	Five times cheaper than acrylic Unlimited textures Can be applied in temps above 35°F	The base coat has to dry out for a week before the next coat can go on Dark colors not recommended as they fade

• Acrylic stucco – Costs $40 to $60/5-gallons and covers 100–250 square feet.
• Cement stucco – Costs about $10–$15/90-lb. bag and covers 100–180 square feet.
• Finishing Coat Stucco costs $20 per bag or about $400 for a whole house.

Stucco Labor Cost

Stucco labor costs range from $2 to $3 per square foot or about 30% of the total cost, with equipment costs adding $0.40 per square foot. The labor cost to install stucco is $35 to $50 per hour per worker, and it takes 3 laborers 3 days to complete the project.

The three coats of stucco needed for a 2,000-square-foot house (1,431 SF of siding) will cost $3,330 to $4,320 to apply depending on whether you want a sand float or trowel finish. The region you live in will better determine the labor cost.

• Natural gray cement with a sand float finish will take 34 minutes per square yard or 4 minutes per square foot = 90 hours for a 2,000-square-foot house. Divide this time by the number of plasterers on the job to see how many days it will take.
• White cement with a trowel finish will take 1 hour and 10 minutes per square yard, or 9 minutes per square foot = 105 hours for a 2,000-square-foot house.

Stucco Labor Process

A wire mesh is wrapped onto the weather wrap around the house, so the stucco has something to grip onto. This first layer of stucco, the scratch coat, is lightly raked over with a tool called a scarifier. The second leveling coat sticks to the scratches and smooths out the surface for the third coat. The third coat is where you can lightly or heavily texture the stucco.

Additional Cost Factors

• Building Permits – The cost of a building permit to install stucco is $75 to $225.
• Scaffolding – Required for walls 14’ or taller.
• Type of Finish – The most popular finishes usually cost more due to the additional time it takes to create the desired pattern.
• Trim – Installing foam stucco trim around your windows and doors will cost $3–$7 per linear foot.
• Condition of Exterior Walls – You’ll have to pay to prep the walls before setup is begun for the stucco.
• One or Three-Coat System – A one-coat system reduces the work by 25% and should lower the cost slightly.
• Quality of Stucco – Better grades of concrete will cost more, adding hundreds or thousands to your stucco siding installation cost, but you’ll save money in the long run by not having to resurface a few years later.

Return to Top

Stucco Siding Cost Estimator

Siding costs will depend if it’s a new install or a re-stucco project, if you’re applying stucco over brick or concrete, and the type of stucco used, whether engineered, synthetic, or traditional stucco.

Stucco siding costs more than the more favored vinyl, wood, or aluminum siding. However, it is the most coveted siding on expensive homes in hotter climates for its unique textured or smooth finishes. The most stucco homes are found in California, Texas, Florida, and Arizona which have quickly adopted this Spanish-style siding.

Stucco Over Brick Cost

Installing stucco siding over a brick, concrete, or masonry surface that’s in good condition costs $3 to $6 per square foot or about $4.50 per sqft. on average. Installing stucco over brick is a great option to add extra insulation to your home.

Stucco adheres to brick without needing a wire mesh unless the brick is in bad shape and doesn’t have 3/8”–1/2” mortar joints, but some installation experts prefer to use a lath for everything as it gives the stucco a better grip.

Stucco Exterior Wall Cost

Building a stucco exterior wall costs between $7 and $8 per square foot, or $58 per linear foot for an 8′ high wall. Most costs are attributed to materials with labor costing $1.68 per square foot on average. A stucco exterior wall must be applied over a supporting structure such as wood, concrete, or brick with a metal or wood lath base and three layers of stucco.

Cost of Stucco vs. Siding

When comparing stucco to other siding costs, it’s cheaper to put vinyl, aluminum, or wood siding up than to install stucco, but stucco can require less maintenance and last longer. It can also insulate a house better than most siding and lessen exterior noise.

Cost of Stucco vs. Siding

Type	Cost Per Square Foot
Vinyl	$3 – $11
Aluminum	$3 – $11
Wood	$2 – $6
Engineered Wood	$2 – $4
Fiber Cement	$6 – $13
Brick	$7 – $15
Stucco	$4 – $8
Steel	$3 – $10
Stone	$10 – $45

Stucco vs.

Brick Cost  

Brick siding costs $8 to $18 per square foot installed compared to stucco’s $3 to $9 per square foot installed, or about double the cost. Despite the expense, a brick exterior will last longer over time than stucco will. Stucco will need to be repaired much sooner than brick will. Brick requires very little maintenance and doesn’t get as affected by moisture as stucco does. Brick can also better withstand heat.

Return to Top

Cost to Re-Stucco a House

A stucco re-coat costs between $3 and $6 per square foot depending on the current condition and texture on the stucco, and what type of finishing will be applied on top. You might need to re-stucco your house if you have found moisture underneath, or you’d like to fill cracks. The cost to re-stucco a home has many factors, like removal and how large the area is that needs to be redone.

Stucco Removal Cost

The cost to remove stucco on metal lath is $1. 05 per square foot and $1.20 per square foot if the stucco is on wood lath. Expect to spend between $900 and $2,100 to remove stucco on the average home. Prices go higher if your walls are over 8’ high and require scaffolding.

Old stucco siding is removed and broken down into movable sizes with hand tools. Add the cost of any necessary flashing and caulking. The old siding will need to be trashed, so you may or may not be charged a disposal fee, depending on the company you hire. You might find it challenging to locate a stucco removal specialist in your area because not many professional plasterers do this anymore.

Stucco Resurfacing Cost

Stucco resurfacing costs $3 to $6 per square foot and may need to be applied if there are several unsightly cracks on the wall. Prices vary depending on the condition of the existing stucco and the finish you want. However, if there is moisture underneath or if the lath is loosening from the studs, the stucco will need to be completely removed and redone.

Stucco Repair Cost

Professional stucco repair costs $8 to $50 per square foot or $200 to $800 on average for a patch and touch-up painting.

• Vertical cracks imply the house foundation is shifting and requires an inspection, which is typically free.
• Horizontal cracks can be patched DIY with caulk and paint, or a bucket of stucco patch for $8 to $20.
• If other siding materials are damaged, siding repair costs $2 to $14 per square foot.

Return to Top

Pros and Cons of Stucco

Pros

• A layer of stucco can add extra insulation to your home, making it more energy efficient, although its R-value is only 0.20 per inch—much lower than wood.
• Stucco can act as a silencer for outside noise.
• It is fire retardant, and the material lasts for an hour in a fire before it starts to deteriorate.
• Stucco acts as a natural repellant to rot, mildew, and mold.
• It only takes 3 to 5 days to install on an entire home or less for smaller projects.
• Stucco can be mixed to produce a custom color.
• It provides a seamless look which accentuates the home’s architectural features.
• It can last up to 50 years and maybe longer.

Cons

• It is a more expensive option for siding a home than wood, aluminum, or vinyl siding.
• It can crack with a shifting foundation or develop moisture problems in heavy rain areas.
• If you wish to paint a new color over it, the old paint needs to be sandblasted off so the fresh paint can stick.

Tips for Maintaining a Stucco House

Maintaining a stucco house is relatively low key. Here are cleaning and maintenance tips to get the most out of your investment.

• Clean – Stucco needs to be washed every once in a while, which you can do without damaging it by using a high-pressure garden hose. Avoid high-powered pressure washing. You’ll want to start at the bottom and make your way to the top, then spray from top to bottom.
• Clean Off Efflorescence – White moisture stains—with white vinegar and rinse off after a few minutes.
• Check Surface for Cracks – Examine the walls for any cracks or holes every few months. If you find any, repair them ASAP.
• Moisture Check – You’ll want to catch the first warning signs of trapped moisture as this can completely ruin stucco as it pulls away from the lath and disintegrates. It can also cause mold issues, which could turn into a more significant catastrophe if not handled right away.
• Add Gutters – Direct moisture away from the stucco with a good gutter system.
• Paint – Consider adding a water-repellent paint over the stucco, but make sure it’s a breathable paint. Flat-finish paints, like acrylic-based ones, are best to use over stucco. This helps make it more water resistant so it can hold up to moist weather conditions.

Return to Top

Types of Stucco Finishes

Choose from a variety of stucco finish types to give your home a look you desire—the looks are mainly based on the types of inclusions between the smooth areas of the stucco in the final layer. These finishes are always done manually. Types of stucco finishes include

• Dash Finish – fine, heavy, or knockdown
• Lack and Skip – fine, medium, or coarse
• Sand or Float Finish – fine, medium, or coarse
• Smooth Finish
• Textured Finish (Worm, Swirl, or Putz) – fine, medium, or coarse
• Santa Barbara – smooth but irregular
• English Stucco – a traditional look

Synthetic Stucco

Synthetic stucco will repel moisture rather than absorb it in the way concrete will, but moisture will still pass through it as a vapor, so it will not seal out water. Concrete stucco will work in the same way if it’s applied correctly. Synthetic stucco also limits the user in the number of textures it can show. Homeowners in the southern climates seem to prefer concrete stucco over synthetic versions.

Synthetic stucco is not an exterior insulation and finish system (EIFS), as it is too lightweight to offer enough insulation. It can also develop water leakage if it’s not applied correctly, especially around doors and windows, thus leading to mold, rotting, and other types of damage. The right expert will prevent this from happening by installing flashing and sealing all joints around the exterior of the home.

Return to Top

Frequently Asked Questions

How Much Does Smooth Stucco Cost?

If you want smooth stucco over an existing stucco wall that has a rough texture, it will cost about $4,000 or about $3 to $6 per square foot. For fresh installations, the stucco can be smoothed out in the final layer.

Cost to Repaint a Stucco House

The average cost to repaint a stucco house is $1.70 per square foot. Expect to pay $850 to repaint a 500 square foot stucco house, and $2,500 to repaint about 1,500 square feet. Stucco paint costs about $4.21/gallon or $29/gallon for elastomeric paint which will stretch with your stucco.

How Long Does Stucco Last on a House?

Stucco can last 50 years or longer on average, or up to 100 years if it’s installed correctly. Most stucco installations will have a warranty of 15 years. Make sure to read the fine print to see what your warranty entails.

How Much Does a Stucco Inspection Cost?

If you see a crack in the stucco or suspect it might have moisture problems, you can get a stucco inspecting for $250 to $350. If the stucco foundation is not easily accessible, then it will cost $100 to $300 more.

How Much Does a Stucco Fence Cost?

The cost to build a stucco fence is $3.50 to $7 per square foot, and stucco must be applied over a supporting structure such as wood, concrete, or brick with a metal or wood lath base and three layers of stucco.

Can You Put Stucco over Cinder Block?

It will cost about $4.50 per square foot to install stucco over cinder blocks. Installing stucco over brick is a great option to add extra insulation to your home. Stucco adheres to brick without needing a wire mesh unless the brick is in bad shape and doesn’t have 3/8”–1/2” mortar joints, but some installation experts prefer to use a lath for everything, as it gives the stucco a better grip.

What Is the Typical Stucco Thickness?

With all three layers put together, the thickness of a finished stucco installation will be 7/8”.

What Is the Price of Stucco Wire?

Generally, mesh netting for stucco is $0.02–$0.04 per square foot.

How Long Does It Take to Stucco a House?

On average, it takes a 3-person crew 3 days to install stucco on a house. For every 1,000 square feet, the installation will take 45–52 hours. Divide this by the number of plasterers doing the plastering to figure out how many days it will take.

Additional questions and answers can be found at Cement.org.

Return to Top

Do It Yourself Stucco Vs. Hiring a Pro

While repairs might be easy to do yourself, do-it-yourself stucco siding installation might be more than you can handle. If you cannot dedicate 95–105 hours to this project (or longer if you don’t know what you’re doing), or you don’t have the time to amass all the equipment needed, then it is highly advisable to call in the experts. If an inferior job is done, then the whole stucco will have to be removed and redone.

How to Stucco

Stucco application usually requires three layers that go over the mesh wiring, so you’ll have to work around the house four times until the work is done.

A wire mesh is wrapped onto the weather wrap around the house so the stucco has something to grip onto. This first layer of stucco, the scratch coat, is lightly raked over with a tool called a scarifier. The second coat, levelling coat or brown coat, sticks to the scratches and smooths out the surface for the third coat. The third coat is where you can lightly or heavily texture the stucco.

You’ll need to buy sheathing materials, weep screeds, casing beads, lath, and a trowel to do the work. Make sure you know how to mix the concrete properly. Be sure to check if your HOA will allow stucco siding before installation happens. If you’re not sure how to stucco, check out the numerous online videos that provide step-by-step instructions.

If you want to know how to repair stucco, horizontal cracks are easily fixed yourself by patching them up. All you need is to clean out any debris from the crack, use some caulk to fill in any small cracks, and then paint over it. For larger cracks, you can buy a pre-mixed bucket of stucco patch for $8 to $20/quart.

Get free home improvement estimates on HomeGuide from trusted stucco companies:

Get free estimates

References

114 HomeGuide Customer Requests

Craftsman National Estimator 2018

Reno Compare | https://www.renocompare. com/projects/siding/stucco-finishes-textures/

Benjamin Obdyke | http://www.benjaminobdyke.com/education-events/what-is-a-stucco-inspection/

Common Issues With Stucco Homes

Warning signs of stucco failure

There are a number of warning signs that can indicate stucco failure. If you notice any of the following common stucco problems with your home, you should call a stucco contractor immediately. 

Lasting water spots, staining, and discoloration

While stucco is designed to naturally retain some moisture, lasting water spots on the exterior of your stucco home can indicate serious problems. Stucco water spots, commonly referred to as staining, can be seen as either white hazy streaks or as dark blotches in the color. When left untreated, trapped moisture can lead to the formation of black mold, rotting wood, and the compromisation of your home’s structural integrity. Often times this is caused by poorly installed, or flat out missing, flashing.

As a homeowner, you should pay close attention to the areas around your doors and windows. They are typically the most common problem areas for stucco homes. However, staining can appear anywhere. While lasting water spots don’t always indicate problems with your stucco, it’s in your best interest to call a professional when you notice one on your home.

Cracking in your stucco

Stucco homes can develop cracks overtime for a myriad of reasons. Shifting land, the wrong mixing proportions, and poor workmanship are a few possible causes for your home to develop cracks. Not only does this look bad, but cracks going deeper than surface level can lead to significant issues for your home.

Unfortunately, cracking isn’t a singular issue. More often than not, stucco cracking will spread as the house foundation settles. Cracks smaller than 1/16 of an inch are common and typically aren’t a cause for major concern, assuming you address them in a timely manner. However, larger cracks can result in water being trapped and leading to issues like those mentioned above. While you may be tempted to simply repair the cracks, all that really does is provide a temporary solution. If the cracks are deep enough, there’s a good chance water’s already seeped through.

Extending below grade

This has less to do with the actual stucco and more to do with improper building practices. Stucco that extends below grade can cause significant issues for your home. When we say “below the grade” we are referring to stucco being applied below where the home’s foundation meets the ground. There needs to be at least two inches of clearance to allow the stucco to properly drain. When a home’s stucco doesn’t have the necessary space or is below the grade, it can trap water and moisture leading to the formation of mold, rotting, cracking, and crumbling. Additionally, the stucco will begin to soak up even more moisture from the ground.

Unfortunately, unless you’re a stickler for details or a home inspector, you likely would have no reason to check your home for this. Unlicensed contractors and shoddy building practices have plagued Southeastern Pennsylvania for years. If you have concerns that your home’s stucco is below grade, it’s best to contact a professional immediately.

Caulking and other waterproofing sealants

Caulk is a material used to seal joints, seams, and cracks against leakage. It’s commonly found along the trim of your home’s doors and windows. When caulking becomes dried, shrunken, or appears to be missing altogether, your home can become susceptible to water intrusion, leading to many of the issues previously mentioned.

Doors and windows aren’t the only areas you need to be aware of though. Many stucco homeowners will experience issues around exterior fixtures such as lighting, decks, and other objects protruding from a home. It’s important for homeowners to monitor these areas to ensure that sealants are in good condition to protect from the outside elements.

Does homeowners insurance cover stucco damage?

Well, the answer is that it depends. For example, if you’ve had homeowners insurance for a number of years, your home’s stucco was installed by a licensed professional, and you only recently became aware of stucco damage, you’re likely going to be covered. However, if you’re missing even one of those three, you may not be so lucky. In fact, stucco damage claims are one of the most denied homeowners claims by insurance companies.

Most insurance companies won’t cover insurance claims for work done by an unlicensed professional. Also, insurance is unlikely to cover the cost if the stucco damage was discovered prior to purchasing a policy. Unfortunately for many homeowners, this is something they don’t find out until it’s too late.

Stucco Repair vs. Stucco Remediation

Whether or not your insurance company will cover your claim, the issues causing stucco failure need to be addressed. At this point in the journey, you’re left with two options: stucco repair or stucco remediation? While both options have their pros and cons, one offers a complete solution whereas the other offers merely a temporary fix.

Stucco repair

The process of repairing stucco involves finding damaged areas and replacing or reapplying more stucco. If your issues are minor or purely cosmetic, stucco repair may prove to be an effective solution. While repairing stucco is often much cheaper than remediation, the major issue with this option is that it fails to solve the underlying issues. As noted above, when the underlying issues aren’t addressed it can lead to a bevy of more significant and expensive problems.

Stucco Remediation

If stucco repair is akin to patching a tire, stucco remediation is like having your tires replaced, brakes checked, and your fluids topped off. Stucco remediation addresses the underlying issues before replacing the home’s stucco exterior. Typically, a home going through the stucco remediation process will opt for a better siding option, such as fiber cement or vinyl siding. These materials are better suited to deal with the harsh conditions faced in the Northeast. Although stucco remediation is more expensive, it’s the better long term choice.

Why choose MHX?

We are a trusted advisor and provider of residential exterior remodeling and renovation projects in Eastern PA. Our mission is to serve homeowners, our employees, our partners, our local community, and people in need around the world. We do this by committing to deliver the highest quality home exterior remodeling and renovation services with honesty, transparency, dedication, passion, and value. See some of our most recent reviews here!

Stucco Failures

Inadequate sealing around windows, doors, and surface joins can result in water getting into the wall system. This penetration gradually causes the material to fail. Poor stucco application practices can also introduce fundamental instabilities into the wall system.

Contact Us

View Past Project Gallery

How Do I Maintain My Stucco Exterior? (Resource Guide)

There is a lot of questions about stucco maintenance and a lot of these are pretty legitimate but isn’t stucco supposed to be virtually maintenance-free?

Stucco is more of a maintenance-free finish it does require a little attention every now and then, just like everything!

The maintenance is very minimal though, providing that you have sound stucco walls that were applied correctly.

It is pretty easy to maintain though and you might be surprised at just how easy it is to maintain.

Washing Your Stucco Walls:

Stucco walls can be washed and should be washed two to three times a year in order to maintain the finish coat’s ability to shine and function the way it should.

You can do this one of two different ways: using a garden hose or a pressure washer.

Using A Garden Hose: You can use a simple garden hose and wash down the exterior of your stucco but be aware that this will only remove a small amount of the dirt and debris that gets collected on your stucco walls over time.

Using a garden hose works best on smooth to semi-smooth textures and will provide a decent cleanse, removing the debris that is loose on the surface.

If you want to get a much better result from using your garden hose then use a medium stiffness brush to get the majority of the dirt removed.

This is a lot more labor intense but will have very different results for your efforts as well.

Helpful Tip: Whenever wetting down stucco walls, manufacturers will recommend starting at the bottom and working your way up for the first initial “wetting down the wall”.

This prevents any staining from occurring that could potentially happen by starting at the top, especially with traditional stucco finishes that tend to absorb water.

Some brushes have a threaded hole on them somewhere where you can attach an extension wand to make the job easier by extending your reach.

If you look on Amazon, you will find many deck scrub brushes that work well for this and are wide as well, cutting the required time it takes to get the job done down quite a bit.

Using A Pressure Washer: A pressure washer is the preferred way to clean your stucco because it is much faster, less labor intense and does a better job than a garden hose would.

If you want to clean your stucco then you will need a pressure washer that is capable of around 1500 psi MINIMUM.

Always use caution when using a pressure washer and wear appropriate safety gear to prevent injury (eye protection, hearing protection, etc.)

Remember that a minimum recommendation will get the job done but a pressure washer that has 2,800 psi will also do the job, a little faster and a little better because of the added psi.

So I recommend a unit around 1,500 – 2,800 psi.

You will want to use a 40 degree nozzle when cleaning the stucco and always be mindful of the distance your nozzle is from the wall and watch the stucco for any damage that may occur from pressure washing.

A good distance to maintain is 12″ – 24″ from the nozzle to the wall for cleaning using a 40 degree tip.

Feel free to experiment with the distance and if you want to try a more concentrated nozzle (25 degrees) then be sure you have the nozzle further away to avoid damaging the stucco finish.

Helpful Tip: The closer your nozzle is to the wall, the better the cleaning power but you will be cleaning less surface area at once.

When your nozzle is farther away from the wall you will get more surface area cleaned at one time but it will not be as aggressive at cleaning the wall.

Using Cleaning Agents On Your Stucco:

You can also use specific cleaners to help remove tougher stains like dirt, mildew, mold and other problematic materials that can cause staining on your walls. 

There are many different cleaners out there to choose from but I will keep the list short to avoid confusion and keep the process as simple as possible.

Plain Dish Soap And Warm Water: You can use warm water and a good quality dish soap to do a general cleaning of mild dust and debris on your stucco walls and  using a good soap (I like Dawn) will give you more cleaning power than just water alone.

Bleach And Water Solution: Bleach can be a great cleaner to use on mold and mildew stains on your stucco walls but be wary of nearby plants, trees or anything else that might be at risk from using bleach.

You can add 1 part bleach to 10 – 20 parts water for a more general type of cleaning on the walls or you can strengthen the mix to 1 part bleach and 5 -10 parts water for tougher stains and “spot treatments”.

Helpful Tip: Always test a small area of your stucco before using bleach in an inconspicuous area of your house or building to see how it reacts and if it harms the color in any way.

Stucco Cleaners From Stucco Manufacturers: There are a few manufactures that have stucco cleaners available and these usually come in the form of a spray bottle that you hook a garden hose up to, making it easy to use and pretty effective too.

The image on the right shows a stucco cleaner from the stucco manufacturer Omega and as you can see, the smaller bottle gets hooked up to a garden hose and you directly spray it onto the wall.

The larger container (gallon) is used to refill the smaller jug (32 oz.) which is good for approximately 1,000 sq. feet of wall.

omega-products.com

TSP Solution: TSP is a great chemical that is used for many cleaning tasks, especially when prepping walls for paint and it can work great for cleaning stucco as well.

A good recipe for using TSP is 1 – 2 cups of TSP to 1 gallon of water.

If the water is warm, it will work better and help to break down the dirt and debris a little better too. Be sure to pre-soak the wall first, from the bottom, working your way up the wall.

Report this ad

Helpful Tip: Start further away from the wall when pressure washing and move closer to get an ideal distance and maintain the distance that works best.

Maintaining Your Stucco Color:

Stucco color can fade over time and sometimes it can even become stained or discolored in extreme cases.

There are a few different things you can do to prevent these things from happening and things you can do to remedy staining issues, blotchy coloring, faded coloring, etc. as well.

Preserving Your Stucco Color:

Stucco Cracks Are Part Of Maintenance…

Stucco is going to crack, it is just the nature of the material but you can fix most of these with a little bit of patience and know-how.

Most of the smaller cracks can be fixed using a little caulking and is something most people can do themselves.

Many of the cracks that form are hairline cracks and I have a more in-depth tutorial on how to fix hairline cracks in stucco that shows you how to go about the process.

Report this ad

Applying Caulking Where It’s Needed:

Applying caulking at specific locations where the stucco meets woo or another material is part of maintenance on your home and I think it should fall under stucco maintenance.

Anytime the stucco meets another material, you will have to apply a bead of caulk because the two different materials expand and contract at different rates, which can cause a gap or crack to form.

Caulking will bridge this gap and flex with any type of movement preventing issues from potentially happening.

These areas should be inspected annually and you should reapply any caulking when necessary (usually 3 – 5 years on average).

An acrylic caulking will blend in best (if done properly) but a silicone or polyurethane caulking will work better and last longer but is difficult to work with.

Stucco Maintenance Cost:

There are minor things that should be done and a lot of them are very low cost and sometimes even free, depending on what you have on hand in and around your home.

On walls that are in very good condition, you may only need warm water, dish soap and a scrub brush, which most people have at their disposal and if not, it would only cost you $20 or less, in most cases.

Other items include caulking and cleaning agents which are very inexpensive too so in general, stucco maintenance is very inexpensive if you tackle it yourself.

The only way you may run into more costly tasks regarding maintenance is if you have neglected your home for a while making a larger amount of work.

If you have repair work that needs to be done, whatever price you pay now isn’t that bad, considering the value of your home and what you are getting for the money.

Traditional Finishes VS Acrylic Finishes:

Coming Soon!

Common Problems That Can Arise:

In the process of cleaning your stucco walls, there can be a couple of problems that can arise so I wanted to briefly touch on these so you know what to expect and what to look out for.

Finish Chipping Off: Sometimes when you are in the process of cleaning your stucco, the finish can come off in some spots.

You can’t always prevent this and it is more of an aesthetic problem (in most cases). This is more likely to happen when pressure washing.

Fixing this can be done but you will need to know what type of finish material you have on your home (traditional or acrylic) and what type of texture.

You will also have to get a custom color match with the correct finish material or paint if you want it to blend in as close as possible.

Stucco Color Is Faded Or Discolored: When your color becomes faded or discolored it is easy to remedy but more work that you might think (in some cases).

You can apply a fog coat to tradition stucco finishes (unpainted) or paint to get rid of the discoloration or fading (after cleaning the area well) but color matching is hard and “spot coloring” areas will still be noticeable.

In order to get the entire wall to look consistent, it is recommended that you color the entire wall (from corner to corner).

A lot of work, especially if you have a larger wall that the color issues are on.

Stucco Has Larger Cracks: Larger cracks (larger than 1/8″ wide) will require a bit more attention and sometimes can be a sign of a more serious problem (1/4″ and larger).

These are better left to have someone come out and look at what’s going on to give you an idea of what to expect.

More often then not, stucco contractors will come out to give free estimates and if you find one that is willing to discuss the problem with you, giving a little insight on what might be causing the issue and how serious it is.

Staining Along Bottom Of Walls: Staining along the bottom of your walls is usually caused by rain falling and hitting the dirt on the ground and splashing up onto the wall. 

You can prevent this by having a barrier of rock, mulch, straw or some other type of material that covers the soil. This is the best way to prevent this from happening in the future.

If the staining has already occurred then you will need to put in a pretty decent amount of effort to remove or fade the staining, especially if it has been accumulating over a few months.

A pressure washer is recommended for these types of tough stains and a 25 degree nozzle at a distance of 8 – 12 inches is going to be my starting point. Go as close as you can to the wall without removing any of the finish but use caution and go slow.

Some Other Helpful Tips On Cleaning Stucco:

• Work on one wall at a time from corner to corner in order to get the best possible results.

  This will ensure that you get every wall as clean as possible and will help prevent the walls from drying too quickly, which could be counter-productive.

• If you have a large house, you can break it up into sections to make the process less labor intense.

  Try to break the process up into two – four days if you need to, working one side of the hose at a time.

• Remember to pre-soak any stucco walls before doing any cleaning.

  This will help to reduce any staining that can occur if you are cleaning surrounding areas that run down the wall.

• Different textures will hold different amounts of dirt and the rougher the texture, the more dirt you will have built up on your walls.

  More frequent cleaning will be required to maintain a clean looking exterior if you have a rougher texture.

• Traditional stucco finishes will soak up water (even dirty water) and will be more prone to staining and discoloration when compared to an acrylic type of texture.

Cost to Paint Stucco House

July 2022

	Item details	Qty	Low	High
	Stucco Painting Cost  Non-discounted retail pricing for: Exterior paint. Latex based, paint and primer in one. Flat, eggshell and semi-gloss finish options. For wood, vinyl, masonry, stucco, brick. Mildew resistant. 15 yr warranty. Quantity includes typical waste overage, material for repair and local delivery.	134 square feet	$60.82	$83.51
	Stucco Painting Labor, Basic  Basic labor to paint stucco house with favorable site conditions. Prep up to 2 hr per 350SF – remove loose paint, spot prime and caulk edges, gaps. Roll / brush 2 coats of paint on siding. Trim extra. Includes planning, equipment and material acquisition, area preparation and protection, setup and cleanup.	134 square feet	$60.82	$83.51
	Stucco Painting Job Supplies  Cost of related materials and supplies typically required to paint stucco house including: masking tape and paper, surface repair material, solvents and cleanup supplies.	134 square feet	$60.82	$83.51
	Stucco Painting Equipment Allowance Job related costs of specialty equipment used for job quality and efficiency, including: 3,000+ psi 4 gpm gasoline powered power washer. Daily rental. Consumables extra.	134 square feet	$60.82	$83.51
	Option: Power Wash Surface Clear surface of solid debris. Apply cleaner with light scrubbing. Power wash and rinse surface.	134 square feet	$60.82	$83.51
	Unused Minimum Labor Balance of 2 hr(s) minimum labor charge that can be applied to other tasks.
Totals – Cost To Paint Stucco House
Average Cost per Square Foot

Custom Calculators with Homewyse Lists

Service Professionals: create a reusable estimating app that is 100% customized to your business. Start with a template or build your own (free; Account sign up required):

For a basic project in zip code 47474 with 125 square feet, the cost to Paint a Stucco House starts at $2.24 – $4.59 per square foot*. Actual costs will depend on job size, conditions, and options.

To estimate costs for your project:

1. Set Project Zip Code Enter the Zip Code for the location where labor is hired and materials purchased.

2. Specify Project Size and Options Enter the number of “square feet” required for the project.

3. Re-calculate Click the “Update” button.

NOTE: *Input the total of the finished surface area AND the area of any openings enclosed by the finished area.

 

Unit Costs: How Pros Price

Unlike other websites that publish pricing from unrelated jobs in the past, Homewyse creates up-to-date estimates from current Unit Costs. The Unit Cost method delivers high accuracy by using location, details and options for the unique requirements of each job. Contracting, trade, design and maintenance businesses rely on the Unit Cost method for transparency, accuracy and fair profits.

Cost to Paint a Stucco House – Notes and General Information

These estimates are for BASIC work performed in serviceable conditions by qualified trade professionals using MID GRADE materials. Work not mentioned on this page and/or work using master craftsman, premium materials and project supervision will result in HIGHER COSTS!

These estimates are NOT substitutes for written quotes from trade professionals. Homewyse strongly recommends that you contact reputable professionals for accurate assessments of work required and costs for your project – before making any decisions or commitments.

The cost estimate includes:

• Costs for local material / equipment delivery to and service provider transportation to and from the job site.
• Costs to prepare the worksite for Stucco Painting, including costs to protect existing structure(s), finishes, materials and components.
• Labor setup time, mobilization time and minimum hourly charges that are commonly included for small Stucco Painting jobs.

The cost estimate does NOT include:

• Costs for removing, relocating, repairing, or modifying existing framing, surfacing, HVAC, electrical, and plumbing systems – or bringing those systems into compliance with current building codes.
• Costs for testing and remediation of hazardous materials (asbestos, lead, etc.).
• General contractor overhead and markup for organizing and supervising the Stucco Painting. Add 13% to 22% to the total cost above if a general contractor will supervise this project.
• Sales tax on materials and supplies.
• Permit or inspection fees (or portion thereof) required by your local building department for your overall project.

References – Stucco Painting

• Product and Supplies Data: Home Depot Paints, Stains and Supplies Home Depot, Jul 2022, Website
• Product and Supplies Data: Lowes Paints, Stains and Supplies Lowes , Jul 2022, Website
• Product and Supplies Data: Menards Paints, Stains and Supplies Menards, Jul 2022, Website
• Product and Supplies Data: Exterior Paint and Supplies Catalog Do It Best, Jul 2022, Website
• The HUD PATH Rehab Guide Volume 2: Exterior Walls U. S. Department of Housing and Urban Development Office of Policy Development and Research, Mar 2011, Editorial Staff
• The Building Estimator’s Reference Book , Mar 2012,
• Home Improvement 1-2-3: Expert Advice from The Home Depot Homer, TLC, Jul 2022, Editorial Staff, ISBN 696213273
• Carpentry and Building Construction, Student Text Glencoe/McGraw-Hill; 6th edition, Jan 2003, Mark Feirer, John Feirer, ISBN 007822702X
• Labor Wages and Costs: CPWAR Construction Cost Book The Center for Construction Research and Training, Jul 2022, Staff
• Project Spending Data: Harvard University JCHS Homeowner Expenditures Harvard University, Jul 2022, Website

Stucco Painting Budget Management

This infographic highlights decisions and site issues that can cause large cost variances in the typical Stucco Painting budget.

Hiring Local Professionals

Our FREE hiring guide helps you hire wisely, get quality craftsmanship and understand fair pricing for your specific project.

Make Homewyse better

We’re an involved community that values your input. So, let us know – did we meet your needs? how can we improve this site? Your comments and sharing are greatly appreciated!

• Send your feedback or questions.
• Save and share Homewyse on social media using the buttons below:

 

How to Repair Stucco – This Old House

Project details

Skill

1 out of 5
Easy

Cost

N/A

Estimated Time

N/A

At first glance, the seamless coat of stucco on the East Boston house looked as bulletproof as a sidewalk, the perfect foil against the harsh wet weather of this coastal city. Yet beneath its lush cloak of ivy, the cement shell was a mess of cracks and buckling, signs that water had gotten in and damaged the underlying wood lath.

When properly installed, stucco (a cement- or lime-based plaster) is about as carefree and long-lived a cladding as anyone could wish—100 years is not uncommon. But when big cracks or blisters appear, the time to make repairs is right away, before the damage grows.

Antonio DiSilva of MJM Masonry performed the remedial work on the East Boston house over ten days, ripping off loose material and patching it with three separate coats. Here’s how to make stucco repair that lasts.

Stucco Recipes

Photo by Reena Bammi

Stucco Recipes

First coat:

• 1⁄2 bag (47 lbs.) Portland cement
• 6 shovels brick or masonʼs sand, slightly damp
• 1 shovel hydrated lime
• 1⁄2 cup acrylic bonding agent

Second and finish coats:

• 1⁄2 bag (47 lbs.) portland cement
• 8 shovels aggregate sand for concrete
• 1 shovel hydrated lime
• 1⁄2 cup acrylic bonding agent

Directions:

1. Shovel the dry ingredients into a wheelbarrow and blend them with a mortar hoe.
2. Add the acrylic bonding agent, then stir in water, a little at a time, until the mix reaches the consistency of buttercream frosting.
3. Too much water will make it loose and unworkable.
4. Once water is added, the mix will stay usable for 30 to 90 minutes before it starts to harden.

Watch The Weather

Freezing temperatures can ruin wet stucco. Wait for nighttime temperatures that stay above 40 degrees before tackling repairs. Hot, dry, windy weather can also interfere by sucking out moisture the mix needs to cure properly. Work in the shade so the stucco doesn’t dry too fast. Between coats, keep the patch moist by covering it with a plastic sheet.

Work Safely

The alkalis in wet cement can cause burns. So when working with fresh stucco, wear gloves or touch the mix only with your tools, not your fingers. Keep a bucket of water nearby to wash any splashes off your skin.

Finish It Right

No patch, no matter how expertly textured, will match the color of the old stucco around it. To do that, you need to apply a pigmented coating over the entire surface. The patch at this house was covered with a thick, sprayed-on acrylic elastomer that bridges and seals hairline cracks. Other acceptable coatings include concrete paints and stains, mineral paints, lime washes, and “fog coats” of pigmented cement. Whichever coating you use, make sure it’s alkaline tolerant and permeable to water vapor. Otherwise, it will be peeling off in no time.

Steps for Repairing Stucco

Step 1: Break Off Loose Stucco

Photo by Reena Bammi

Whack it with a hammer, or a hammer and a cold chisel, taking care not to damage the underlying wood lath supports. Eye protection is a must.

Step 2: Chip Away At The Edges

Photo by Reena Bammi

Continue until you reach stucco that’s firmly adhered to its lath. Cut any metal mesh with snips.

Step 3: Cover The Exposed Lath

Photo by Reena Bammi

Using a utility knife, trim a piece of grade-D builder’s paper to fit tightly along the boundary where the old stucco meets the exposed wood lath. Fasten the paper to the lath with roofing nails, then put a second layer of paper on top of the first.

Step 4: Add Mesh

Photo by Reena Bammi

Place galvanized metal lath over the paper and trim it tight against the edge of the stucco. Snips with offset handles will make this job easier. Drive more roofing nails through the mesh and into the wood lath.

Step 5: Mix The Stucco

Photo by Reena Bammi

Following the first-coat recipe, stir up a batch of stucco, using a wheelbarrow as a mixing bowl. The acrylic bonding agent added to this mix improves the adhesion of the new stucco to the old.

Step 6: Sling It

Photo by Reena Bammi

Wet the edge of the old stucco so it won’t suck moisture out of the patch and weaken the bond between old and new. Scoop fist-size wads of wet stucco onto a brick trowel and toss them against the wire lath until it’s completely covered. Smooth the mix with a finishing trowel, then pack it against the edge of the existing stucco with a brick trowel. Keep adding more material until this layer is about 1/2 inch below the existing stucco surface.

Step 7: Scratch It

Photo by Reena Bammi

When the patch loses its wet sheen, score its surface to improve the bond to the next coat. Tape a plastic sheet over the patch to keep it from drying out.

Step 8: Apply Second Coat

Photo by Reena Bammi

Wait seven days, then remove the plastic and mist the patch with water. Mix up a batch of stucco following the second-coat recipe, and trowel on a 3/8-inch-thick coat, working from the bottom up. Pack down the edges with a brick trowel. Wait for the wet sheen to disappear, then trowel the patch smooth, just below the level of the existing stucco. Cover again with a plastic sheet.

Step 9: Put On The Finish Coat

Photo by Reena Bammi

After three days, remove the plastic, mist the patch, and mix up a fresh batch of stucco, following the finish-coat recipe. Different textures require different techniques. To match this wall’s original “dash” finish, DiSilva scooped small globs of wet mix onto his brick trowel, then flicked them against the wall until they were flush with the old surface.

Step 10: Wait To Paint

Photo by Reena Bammi

Let the patch cure for a week before painting it and the rest of the wall. Under a coat of heavy-bodied acrylic elastomer, the patch is invisible.

---

Tools:

Tools & Materials

Siding Technical Papers – Stucco Homes in PA and NJ: Why They’re Failing and What to do as a Homeowner

Tuesday, March 6th, 2018 by Michael Gabrian

There has been a massive problem for homeowners in Pennsylvania and New Jersey who own stucco homes built within the last 15 to 20 years. Tens of thousands of homes are seeing extreme water damage hidden under the stucco exterior of their homes.

What does this mean for homeowners with stucco siding?

If this issue is not taken care of, moisture will continue to accumulate and make the problem worse. This can pose hazards to the inhabitants’ health, it can severely drop the value of your home, and it could leads to repair costs in the six digits.

A lot of what it comes down to is the quality of work that the installers use. A lot of complaints come from either an inferior stucco replacement or just shoddy installation. If there is improper spacing and water management, there is an opening to a bunch of problems.

Let’s talk a bit more about the details of this problem and what you can do to prevent any more damage to your stucco home.

The problem

So what exactly went wrong? People have begun to steer clear of stucco when buying homes, but is stucco actually the problem?

The fault really lies with the contractors that cut corners when applying the stucco to the homes. Stucco is naturally absorbent, which isn’t actually a problem if you apply proper water management measures to the home. With incorrect installation, water and moisture finds it’s way under the stucco and doesn’t have a way out. This is where mold and mildew will begin to form which can ultimately form into black mold or compromise the integrity of you home. Some people have reported their siding has turned into a mush from the moisture. I’d suggest combatting this using BlueSkinVP, a water resistant barrier, under your stucco. This will prevent any trapped moisture from eating away at your home’s wooden structure.

One of the big issues is that it’s incredibly difficult to actually know if you have any water damage with stucco. It just grows for years without your knowing. You won’t actually know that there is a problem until you see stucco tears forming on the exterior. The worst part is that some homeowners had to replace their stucco siding just a few years after installing it!

Since most homeowner’s insurance policies don’t usually cover mold or poor construction, people are left paying out of pocket for what could be anywhere from tens to hundreds of thousands of dollars.

How to prevent damage from moisture from getting caught under your stucco siding

The solution really ranges based on how bad the damage to your home actually is. If it’s minor damage, you could probably just add a water resistant barrier and install better flashing to prevent the problem in the future. For some people, the only answer might be to take down entire walls that have been compromised far beyond repair.

For sure, though, you’ll need to install proper flashing and a water resistant barrier. We at Global Home Improvement highly recommend BlueskinVP as a water resistant barrier. It’s a peel and stick exterior barrier that prevents any moisture from getting in and damaging the structure of the home, but it also allows breathability for interior vapor to escape. Other water barriers require nails, which ultimately require you to force hundreds of holes into your barrier opening your home up to a lot of damage potential. This will at least protect the interior of your home. To repair the integrity of your stucco, you’ll need to have a reputable contractor to come and make the repairs.

What can you do right now?

Although it’s not easy to get a view of what’s going on under your stucco siding, there are a couple of quick easy things you can do to see if your home is in danger.

The first thing you should do is check your walls for brown streaks. Your most vulnerable points will be near windows, intersecting walls, etc. This is where flashing work is emphasized and some companies will cut corners, so it would be best to check there first.

If the damage is a bit more severe, you may see signs inside your home. You should be able to see some of the same water stains on walls, but also look for any wet spots on your floors and carpets. You may also be able to smell that musty, mildew smell in your home. That’s also a bad sign.

You could hire a specialized stucco inspector to conduct moisture tests to see how bad your damage might be. They’ll be able to determine how much moisture you may have built up behind your stucco and if it’s caused any damage.

It might also be a good idea to call up a more reputable company, like Global Home Improvement to assess the area and see if you have any weak points and where you could benefit.

Conclusion

If you own a stucco home in PA or NJ, there is a very high chance that your siding was constructed poorly. This pertains to recent and dated installations.

The problem is that stucco siding just isn’t meant for this type of climate and environment. It’s best in dry climates where it won’t be exposed to a lot of moisture. If you’re looking for a durable, strong, and weatherproof siding option that won’t be damaged from moisture, consider a Hardie siding replacement.

If you think you might have water damage or really aren’t sure, play it safe and have someone come check it out.

Back to Previous Page

Back to Technical Papers

Polyurethane stucco decor “Stucco House”

Quick selection of decor

• Decor

  Interior decor

  Facade decor

• Category

  —Decorative beamsDecorative elementsWood imitation boardsWood imitation consoles, beltsStonesCornices for lightingEaves with a smooth profileEaves with ornamentsCaissonsGlue and related. materialsColumnsBracketsDomeMoldingsIlluminated moldingsRadial moldingsSlipsFloor plinthNichesFrame archesFraming balustradesFrame doorsFrame mirrorsFrames for fireplacesFrame windowsOrnamentsPilastrsWindow sillsSemi-columnsPlinthsCeiling rosettesRustas and panelsSandriksStatuesCorner elementsFriezes and architraves

• ARXAT&ART

  Decorus

  Fabello Decor

  Harmony

  Leptonika

  Modus Decor

  Orac Axxent

  Orac Decor

  Tesori

  Europlast

  Regent Decor

• Flexibility

  Flexible

  There is a flexible analogue

  Not flexible

Choose a decor

Discounted goods

Product catalog of the online store “Lepnoy Dom”

Our partners:

Our company has been successfully operating in the building materials market for more than five years. We are engaged in the sale of decorative moldings made of polyurethane. The Stucco House catalogs contain all kinds of finishing materials for decorating facades and rooms: cornices, moldings, ceiling rosettes, panels, corners, skirting boards, niches and much more. You can buy decor for decorating an apartment, office, house, shop, restaurant, hotel complex, beauty salon and even a sauna from us.

Europlast Oracor Orac Axxent Modus Decor Regent Decor Prestige Decor Fabello Decor

Polyurethane stucco

9000 9000 9000 9000 9000 9000 9000 9000 9000 9000 9000 9000 9000 9000, Sulpent decor received a new birth with the advent of synthetic polyurethane. The unique properties of this material led to the gradual displacement of stucco from natural raw materials. The small mass of products, ease of installation, ease of maintenance, practicality of operation, durability and low cost significantly contribute to their growing popularity in the building materials market. And the possibility of painting and giving polyurethane a resemblance to stone, wood or metal, allows you to successfully use artificial stucco molding in any architectural ensemble.

Benefits of Lepnoy Dom:

Customer focus. With years of experience and deep knowledge in the sale of polyurethane products and project design, our staff will help you choose the right decor or finishing material. Company managers are ready to provide detailed advice on the use of each stucco element, as well as its combination with other architectural details and styles.

Large assortment. Our catalogs feature affordable, superior quality finishes in a variety of shapes, sizes and architectural styles. The range of products is so extensive that it allows you to choose stucco molding for the most daring author’s ideas and projects.

Quality product. The Stucco House company works with products of such well-known manufacturers as: Europlast, Regent Decor, Modus Decor, Fabello Decor, Prestige Decor, Orac Decor and Orac Axxent. The products of these brands have a quality certificate and are characterized by 100% reliability.

Honesty and integrity. Valuing our reputation, we work exclusively without unnecessary markups and conscientiously. If you find a defect in the product, we will refund the money.

Convenient service system. We have a practical customer service system. A convenient work schedule allows you to establish direct contact for consultation and ordering, and e-mail guarantees a round-the-clock opportunity to leave a request. Your chosen decor and related materials will be delivered as soon as possible, both in Moscow and within the Moscow region.

Cooperating with us, you get:

• a unique opportunity to purchase a quality product at a loyal price;
• first-class service and detailed advice on all issues;
• fast and convenient delivery;
• a sea of ​​positive emotions.

ᐈ Stucco house on Kommunisticheskaya street on Kommunisticheskaya, reviews and photos of Decor, interior items in Moscow, phone numbers and addresses on Yell.ru

ᐈ Stucco house on Kommunisticheskaya street on Kommunisticheskaya, reviews and photos of Decor, interior items of Moscow, phone numbers and addresses on Yell.ru

8 (499) 390-60-038 (499) 390-60… — show

8 (499) 390-60-038 (499) 390-60… — show

About Stucco House on Kommunisticheskaya Street

Suggest changes

Report closure

creating comfort and beauty in your home or workspace. Thanks to interior items, you can either simply make a certain accent in the room, or completely update the look of the space and the mood that it gives. Whether you need a cute item made of unusual material or something ergonomic, designed to accommodate items or store them, you have the opportunity to consult with a sales assistant about whether your potential purchase will fit into the overall ensemble.

You can also find household goods here. In such specialized household outlets, they offer both to take a specific piece of goods, and, if necessary, how to buy both convenient devices for the home and household chemicals, which, by the way, are more profitable to take in large packages.

You can pay for the goods in cash and using a web wallet or by card. You can pick up the goods yourself or arrange delivery by mail, transport company, courier.

Store rating on our recommendation service – 5.

To obtain the necessary information, call +7 499 390-60-03 or go to the website lepnoydom.ru. Stucco house company is located at the address: Moscow region, Mytishchi, Kommunisticheskaya street, 25G.

Information copied from Yell.ru – https://www.yell.ru/moscow/com/lepnoy-dom_11928969/

Delivery 5

Delivery

Delivery by Courier

Delivery by Postal Service 9006

Pickup

Grade 3

Online store

Conventional

Wholesale

Methods of payment 4

Cashless Calculation

Web Pores

Cash and structures

Type of workshop 1

Online store

Goods 1

Household goods

Anatoly Danilov

167

5

3 years ago

Had experience with this company. Ordered window sills from them. I liked that they have a lot of choices. Delivery was made on the specified day. As for the quality of the elements, no complaints!

Useful

Reply

Share

Stucco house on Kommunisticheskaya street +7 499 390-60-03 Moscow region, Mytishchi, Kommunisticheskaya street, 25G Maksimenko

9006

51

5

3 years ago

Acquired two statues of a lion and an eagle as decor, the quality is excellent and the price for such beauty is quite adequate. Delivered safe and sound, service and purchase was satisfied.

Useful

Reply

Share

Stucco house on Kommunisticheskaya street +7 499 390-60-03 Moscow region, Mytishchi, Kommunisticheskaya street, 25G

9006 Yuliya 9006

202 135

5

3 years ago

I bought a statue of a pissing boy in this store as decoration near our fountain in a country house. It goes well with the fountain. I think the cost of 9 thousand is quite adequate!

Useful

Reply

Share

Clip House on a Communist Street+7 499 390-60-03Moskovskaya region, Metishchi, D 25G

MOHAXEJAK 9000 9000 1

9000 9000 9000 9000 9000 9000

006 5

4 years ago

What a great online store for me. I bought docking glue here. I would also like to note a good range of materials for decoration. I was satisfied with the purchase here)))

Helpful

Reply

Share

Stucco house on Communist street

See also

Building and finishing materials in MytishchiBuilding materials in MytishchiFinishing materials in Mytishchi

90,000 stucco molding in the interior – types and features of the use of stucco molding in the apartment, the main points of stucco molding – useful blog VIT42

Content

1. Historical certificate
2. stucco moldings in architecture
3. of which materials are made by
4. Variants of use

9013 in which interiors are used in which interiors are used.

5. Modern Interior Stucco and Decoration
6. Useful Implementation Tips
7. Bedroom Interior
8. Kitchen interior
9. Entrance hall interior
10. Living room interior
11. Nursery interior
12. Bathroom interior
13. Let’s sum it up

Stucco decoration in the past was a sign of luxury, if it looks original – After the spread of styles similar to high-tech, it was put in a bad light. It was believed that this is a cheap element, so it was rarely used in the interior. Nevertheless, the cyclical fashion is always relevant. Stucco is again actively decorating houses and many recognize that this decor fills the atmosphere with nobility. In this section of the blog of our Vit42 online store, you can learn more about stucco molding and its use in the interior.

Historical reference

Stucco molding is an original decoration of a relief type, used as a decoration in the exterior or interior. Indoors, it was added back in the days of Ancient Egypt. They worked with materials in Ancient Greece, Rome, and therefore stucco is rightly considered the oldest decor tool. Several centuries ago, the interior was overloaded, complex. Then they created not only simple ornaments, but also realistic portraits, stories related to past events, belief in gods. The fame of stucco was noted in the era of classicism, baroque, empire.

The heyday of decorativeness fell on the baroque, when pomposity, ornateness, and pretentiousness were highly valued. The masters competed with each other to show their experience and hone their techniques. It is amazing that with their hands they did such a difficult job – they brought to life objects that people still admire. Just take a look at this photo!

Stucco molding in architecture

When the time of classicism came, the architecture became restrained, but it cannot be called truly modest. Art Deco, combining modern and neoclassicism, is probably the last of the styles in which colorful ornaments, chic, and expensive modern materials were confidently put on.

Now the stucco is not the same, it has been greatly improved, with different features. Examine the catalog of the online store https://vit42.ru/catalog/. You will see that today decor of this type is presented at an affordable price, in the form of separate parts, easily combined into one interesting product. Received for many years will be included as an element of the interior, as the quality of workmanship is reliable. The modern procedure for creating stucco is not similar to the work of ancient artists, but the visual result is just as naturalistic.

What materials are used to make

Initially, stucco molding was a water mixture of gypsum with the addition of an adhesive solution and natural fractions – limestone or marble. However, this type of material does not tolerate external negative influences – it cracks over time, loses its brightness, and quickly becomes dirty. Now stucco is made from polyurethane foam and other similar materials. Polyurethane foam does not crumble, it is strong, durable. With a competent device, no connections are visible on a single composition, it seems to be solid. Such stucco is easy to install, restore if necessary. Traditionally, stucco is white, but now it is available in gold, beige and other colors. You can choose an option for different color themes of the interior. Let’s take a closer look at each material.

Gypsum

It contains sulphates, natural materials, which are fired and crushed. The output is a viscous composition. From it it is convenient, the necessary forms are quickly molded. Service life is long.

The disadvantage of gypsum is its heaviness, overall devices should be installed by experienced specialists. Note that not in every typical building it is appropriate to install large gypsum objects with an impressive weight, but small ones are suitable when you need to fill voids.

Plaster stucco molding is made as follows:

• the composition is poured into a suitable mold, developing the necessary proportions in advance;

• wait for the mixture to harden: it takes up to 1-2 days, the total duration depends on the size.

After the correction is carried out manually and using tools. Further used for its intended purpose. That is, it is not difficult to prepare a solution for work. It is more difficult to make the thing express sophistication, it is appropriate to infiltrate the room.

Pros:

• High price. It is compensated by a long service life, environmental friendliness of the material, its strength characteristics.
• The ability to quickly bring any idea to life. When the surrounding design is boring, then update the situation with plaster components. If necessary, it can be dismantled.
• This material is used to create architectural stucco decor for the home. With it, your interior will become much more interesting, but large decorations require strengthening.
• Environmentally friendly. Gypsum does not harm nature. It is non-toxic and does not harm humans.

Polyurethane foam

Polyurethane stucco is a composition based on heterochain polymers, and this is a very affordable, inexpensive building material. It is high-strength, resistant to moisture, so it is often used in construction, achieving a variety of geometries. It is the leader in demand among interior experts and hobbyists. See examples of products in our catalog section – https://vit42.ru/catalog/lepnoy-dekor/interernyy/.

Since the product is based on polymers, this makes it suitable for high humidity applications. Therefore, it is suitable in the kitchen, dining room, bathroom and other rooms.

Pros:

• Performance. Outwardly and in terms of reliability, polyurethane objects are not inferior to gypsum and even surpass them. The material is good for the interior and for external processing of the building, for example, balconies.
• Many variations. Polymers are plastic, it is possible to make figures of any shape from them.
• Resistant to temperature extremes and fungus. Install lamps and other light sources nearby, as the material is not afraid of thermal exposure. Also, it does not collapse from moisture, so mold or fungus does not form on the surface after prolonged use.
• Quick and easy installation. You yourself will make a suitable type of surface without calling a professional. The installation of stucco molding is carried out with special glue, even the overall decor is light in weight.
• Maintainability. The material is not afraid of damage, but if there is, then the composition can be reanimated with the same polyurethane foam. The surface is easily updated, covered with paint.

Styrofoam

Economical, lowest price. Stucco molding from polystyrene is performed using foamed polystyrene foam. Plasticizers are also introduced in production. Styrofoam stucco is light, but at the same time plastic. With it, you can get any form. Styrofoam is resistant to negative external factors, but does not withstand mechanical stress.

Pros:

• Does not weigh down the surfaces to be added.
• Able to embody the structure of wood, stone and other materials.
• Will not fade or flake unless physically impacted.

Among the minuses, we note fragility. Breaking a foam object is easy, but replacing a damaged one is not difficult, not expensive.

So, we have listed all the advantages of materials, given detailed information about them.

Applications

A single stucco image is created by joining multiple pieces. The process is similar to assembling a constructor. There are many types of jewelry, consider the common ones.

Skirting boards

These are strips covering the area where the floor and wall join. Usually skirting boards are made of wood or plastic. They are taken under the type of flooring, but there are exceptions.

• Cornice. A plank with different thicknesses has a decorative purpose and at the same time covers the angle between the ceiling and the wall.

• Molding. This is a bar with volume. Behind it, compounds of different or homogeneous materials are hidden (for example, the place where the wallpaper converges). Suitable for decorating arches, frames and cornices.
• Bas-relief. It is a sculptural structure that protrudes above the plane. Even in ancient art, they appreciated how well the bas-relief fits into the interior. Details of this type are chosen by those who like the architecture of past centuries.
• Socket. A multi-shaped stucco molding, which is designed to improve the quality of fastening a wall lamp or other lighting device.
• Bracket. This is the fragment that supports the protrusions. It is customary to decorate it with curls.
• Column. Performs its direct role, may have curly elements. Traditionally, the decor consists of several parts: the lower support, the actual column, pilaster or capital, it is also called crowning.
• Niche. It is mounted on the wall, it is a floor covering for installing fonts, statues or other similar items.

In what interiors is used

Stucco molding in its classical form is applicable not in all styles. It’s not just about patterned cornices, columns or skirting boards. Examples of directions:

• baroque;
• Empire;
• art decor;
• modern;
• rococo;
• renaissance, etc.

A small number of elements are allowed in art nouveau or gothic. The stucco decor in this case has a different design, different from the one we are used to seeing in the classics.

So, both interior and facade stucco molding is appropriate mainly in styles that support the demonstration of chic, pomposity. It is still associated with wealth, despite the fact that experts often swear by excess, arguing that this way the available space is overloaded. Nevertheless, in any traditional setting, it is possible to use stucco interspersed. It can be a small ornament or a full-fledged decoration of the entire wall.

Excessive decors are out of place only in modern design, concise and without frills. Even if an insignificant addition is implemented, it will seem superfluous. In the style of classicism, stucco is allowed without restrictions.

Stucco and decoration of modern interiors

On walls and ceilings, decoration helps to enrich the environment without losing its elegance.

• Decor will create unique images in the interior – the visual depth of the ceiling or walls.

• It visually expands the room, or vice versa, makes it more comfortable.
• Various planks with embossed patterns cover gaps and joints, correcting recent or past repairs. They effectively hide the connections of various materials.
• A concealed LED lighting system is sometimes installed behind the stucco ceiling molding.
• Ceiling chandeliers are made with patterned rosettes, pre-selected size.
• Decorative architraves, medallions or garlands are a great way to set niches in an unusual way. They will enrich the plane of the walls, arches or window frame.

Stucco is an effective way to imitate a coffered ceiling, while it will cost less than the original, will be elegant, not weighing down. Unusual openings decorated with plaster. Bas-reliefs are often introduced in modern apartments.

In past centuries, stucco was covered with gold leaf or paint. Now there are a lot of original models. At the request of the customer, the installed decor is painted in any shade (wood or marble). It can be gilded, silver-plated, aged, dressed to look like some kind of material.

Before you work in any room with a three-dimensional decoration, think in advance about what the final result will be. Avoid excess patterning, clumsiness. In addition, stucco is appropriate for ceiling heights of at least 3 meters. Also, do not use it in rooms up to 6 square meters – this threatens with clutter, crampedness.

Useful implementation tips

Stucco is required primarily for beauty. That is why it must impress. With limited space, it is allowed to install stucco elements in fragments – to process paintings, mirror surfaces using several moldings. In rooms of more than 10-12 square meters there are plenty of opportunities for the introduction of stucco molding.

If you are going to add a mirror frame, first look at the thickness of the decor. Overall models look good with a wide decoration. If the size is small, then choose the appropriate decorating. But when a mirror with LED-backlight or other unusual features, they do without decor at all. Work on the pictures in the same way. Of the other nuances, we note:

• The socket is required for heavy fixtures. It sets off the beauty of the lighting fixture. You can’t do without it if the room is decorated in Empire style.

• Often they prefer to work a lot with the sleeping place in order to achieve the impression that the bed is in the royal palace. Highlight the bed in the room with columns. They also try to make the dressing table brighter.

• Stucco components are available not only in white. Technologies allow the production of decorative objects of all colors.

To make the apartment in the same style, take forms with the same ornament for all independent rooms. Or decorate nightstands, cabinets, in order to provide a combination with the overall design.

Stucco is beautiful, but only when appropriate.

Bedroom interior

If you are not a fan of modern styles, then boldly express yourself, fantasize. Of course, the main piece of furniture that accentuates the decor is a bed. It is what sets the mood in the room. We list the common areas that are relevant for bedrooms.

Classic

Solid wood furniture is appropriate here. Not bad if it is made of expensive woods (oak, walnut, cherry). Carving is allowed, with elegant monograms, as well as accessories with glitter. Use fabrics generously—heavy drapes, bedspreads, tulle, and others. Place columns, sockets for lighting fixtures with strict forms. Decorate one of the walls with a fresco.

Minimalism

The rule applies here: the less elements surround the inhabitant, the better. Forms are better to take simple, unpretentious. At first it seems that stucco is meaningless here, but it is not. Stucco molding is introduced carefully, wall moldings will do. Treat the panels, figures, covering with metal dust or equipping the backlight to make everything futuristic, do not forget about unusual elements.

Romantic

Be bolder with landscape bas-reliefs depicting insects, leaves, animals. It is nice that they are performed in white or pastel colors. The more intricate curves, the better – so comfortable, freer.

Kitchen interior

If the kitchen is spacious, let your imagination run wild. Any style is appropriate. Cover the non-working wall of a huge room with voluminous stucco molding with a 3D effect. Combine dissimilar patterns on the wall, arrange them. In this case, the type of faucet and sink, the type of furniture are important. The classics are appropriate – molding, imitation of masonry, borders. Panels with baroque ornaments will look bright.

We recommend contacting a technician. He will consider how to introduce stucco elements that can reduce the cost of costs, on the contrary, add luxury to inconspicuous areas. Of course, let us know about your ideas when ordering a design. But at the same time, listen to what the specialist says, so that what was conceived in the final form looks harmonious.

A kitchen space needs functionality first, and attractiveness second. Put practicality above all else. Existing kitchen equipment can be decorated by decorating the hood, putting a border on the ceiling or adding brightness in the outlet area. But think about the fact that this should all be amenable to quick cleaning. Polyurethane decor is recommended for the kitchen.

Entrance hall interior

Guests first of all get into the entrance hall – the “visiting card” of the whole apartment. If the floors are even, without flaws, it is pointless to sheathe them with panels, losing free centimeters. They imitate panels with stucco, for example, with moldings. It’s practical, not expensive. The entrance hall acquires elegance, spaciousness. It is appropriate to place sockets on the lamps. If this is not enough, fill the space above the door with overlays. It is acceptable to finish paintings, mirrors, framed too modestly. Thus, you can focus on certain elements in the apartment. But do not overdo it, the “hall” of a residential building should not resemble a museum.

Living room interior

To make stucco look luxurious, you need to respect taste and sense of proportion. Then the room will be made in such a way as to comfortably receive guests or relax with the family in their free time. It is necessary that the decorated come to the fore. For this purpose, large objects are specially selected. Try to cover the stucco with dark colors to achieve the best combination with the decor. If you want to achieve a noticeable conciseness, put separate elements that do not draw attention to themselves in size and pattern. Enter frescoes or hand-painted with light milky or ivory stucco. If moldings are adjacent to decorative plaster, then it is better when they are combined with the general range.

Exquisite wall decoration – figured facings. If you like walls without additions, enter patterned additions to the ceiling, cabinets, and lighting fixtures. An interesting idea is the construction of a decorative home fireplace, the main highlight and source of comfort. Feel free to use polyurethane, it does not require careful maintenance, does not crumble, and creates the impression of an expensive one.

Interior of a nursery

With stucco elements, a nursery is fabulous, cozy, it’s nice to be here. Parents can not be afraid of excessive saturation. Come up with original stories on the wall that the child dreams of, framing them with a curly cornice or other overlays.

The nursery should be easy to use so that the little “owner” can do the cleaning himself. If the child’s age allows, get his opinion, organize everything as you wish.

Bathroom interior

Although standard houses in Russia are more common with compact bathrooms, sometimes they are spacious. Often they are combined with a bathroom, then feel free to show your refined taste. Considering that polyurethane moldings are not afraid of washing, when planning a bathroom design project without restrictions, include something openwork, not forgetting about a sense of proportion.

A beautiful Empire style — imagine a bowl on bizarre legs, graceful patterns adorn the mirrors. And a panel depicting Poseidon or Gorgon Medusa in black and gold will impress those who enter and see such a decision.

Summing up

We talked about a decorative element that has stood the test of time and remains popular. Of course, it does not apply everywhere. Stucco then falls into disfavor, then again in high esteem. But fashion is cyclical, changeable, but remember: your house – your rules. Only you decide in what style the apartment will be decorated, what pattern or border is appropriate. If you like classics, sophistication, “square” allows, then why not add stucco structures at home, even in a typical apartment. Create an atmosphere in your home that will be pleasant.

If there are difficulties, no experience in design preparation, implementation of the original furnishings, contact the profile designers, informing about the wishes. In this case, you will be sure of the appropriateness of the stucco decoration and its correct introduction.

LEPNOY DOM LLC, Penza (TIN 5837075554), details, extract from the Unified State Register of Legal Entities, address, mail, website, telephone, financial indicators

Refresh browser

Refresh browser

Capabilities

Integration

About the system

Statistics

Contacts

CfDJ8No4r7_PxytLmCxRl2AprPruUUw3kL5X4u41BxfmVpLQe5TLdFfojqf8A94wJ0p-CLmTEuaTOZhFk93WPd1TGzcodsNMJcThgjvpdOUeQ53gkRMoBChMT6d0hkf9yWKb0I16TwKv4

Description of the search engine

search encyclopedia

TIN

OGRN

Sanction lists

Company search

Head of the organization

Court cases

Affiliation Check

Execution proceedings

Organization details

Information about the beneficiaries

Organization’s current account

Credit risk assessment

Checking the blocking of the current account

Number of employees

Authorized capital of the organization

Bankruptcy check

Date of registration

Checking the counterparty by TIN

checkpoint

OKPO

Tenders and public procurement

Legal address

Analysis of the financial condition

Organization founders

Financial statements

OKTMO

OKVED

Company Comparison

License check

Extract from the Unified State Register of Legal Entities

Competitor analysis

Organization website

OKOPF

Registration Information

OKFS

Branches and representative offices

OKOGU

OKATO

Register of dishonest suppliers

Company rating

Check yourself and the counterparty

due diligence

Banking licenses

Scoring of counterparties

Alcohol licenses

Media monitoring

Signs of economic activity

Reputational risks

Compliance

Company LEPNOY HOUSE LLC, address: Penza region, Penza, st. Ryabova, str. 4B office 13 was registered on 03/20/2019. The organization was assigned TIN 5837075554, OGRN 1195835006597, KPP 583701001. The main activity is wholesale trade in timber, building materials and sanitary equipment, in total 42 types of activity are registered according to OKVED. There are no connections with other companies.
Number of co-owners (according to the Unified State Register of Legal Entities): 1, General Director – Belyaev Dmitry Andreevich. The size of the authorized capital is 10,000 rubles.
LEPNOY DOM LLC did not take part in tenders. There are no enforcement proceedings against the company. LEPNOY DOM LLC did not participate in arbitration cases.
Details of LEPNOY DOM LLC, legal address, official website and extract from the Unified State Register of Legal Entities are available in the SPARK system (demo access is free).

Full check of counterparties in SPARK

• Unpaid debts
• Arbitration cases
• Communications
• Reorganizations and bankruptcy
• Other risk factors

Full information about the company LEPNOY DOM LLC

299₽

• Company registration data
• Manager and principal owners
• Contact information
• Risk factors
• Signs of economic activity
• Key financial indicators in dynamics
• Check according to the registers of the Federal Tax Service

Buy
Example

999₽

Yearly change monitoring enabled

• Company registration data
• History of changes in managers, names, addresses
• Full list of addresses, phone numbers, websites
• Data on co-owners from various sources
• Related companies
• Activity details
• Financial statements for several years
• Financial assessment

Buy
Example

Is free

• Complete information report – SPARK PROFILE
• Adding contact details: phone, website, mail
• Add description of company activities
• Download logo
• Loading documents

Edit data

SPARK-Risks for 1C

Reliability assessment and counterparty monitoring

Learn more

Application for demo access

Applications with corporate email are processed faster.

Logging into the system will be possible only from the IP address from which the application was submitted.

Company

Telephone

We will send a confirmation code

Email mail

We will send a link to enter

By clicking the button, you agree to the terms of use and processing of personal data

Stucco, interior and facade decor in Moscow

Login

Registration

Comparison

0

Deferred

0

my basket

0

0
R

Issue

• New
  New

• Hit
  Bestsellers

• %
  Discounts

Manufacturers

A. Grifoni

A.S. Creation

Andrea Rossi

Anna French

Aquarelle Wallcoverings

Architects Paper

Arlin

Arte

ARTE Lamp

ArtGlass

All manufacturers

Home

Stucco

Interior decor

architraves

Cornices

Caissons and domes

brackets

moldings

niches

framing arches

door frame

ornaments

Skirting boards

Sockets

Sandriks

Corner elements

Decorative fireplace elements

Facade decor

arched frames

architraves

Balusters

Additional elements

Keystones

Cornices

Brackets-pedestals

Post caps

overlays

platbands

ornaments

Foundations

slopes

window sill elements

Brand

Orac Decor

Europlast

Plintex

Stucco adhesive

Docking adhesive

Mounting adhesive

Universal glue

Concealed lighting

Eaves for hidden lighting

LEPNOY DOM LLC, Penza, TIN 5837075554, contacts, details, financial statements and extract from the Unified State Register of Legal Entities

+7 841 275-84-75
+7 966 800-97-77

—

---

Contact information out of date?

Edit

---

Legal address

440004, Penza region, Penza, st. Ryabova, building 4B, office 13

To show on the map

PSRN	1195835006597
TIN	5837075554
CPR	583701001
OKPO	40581975

OKOGU code	4210014 Organizations founded by legal entities or citizens, or legal entities and citizens jointly
Code OKOPF	12300 Limited liability companies
Code OKFS	16 Private property
OKATO code	56401377000 Pervomaisky
OKTMO code	56701000001 Penza

Registration with the Federal Tax Service

Registration number 1195835006597 March 20, 2019

Inspectorate of the Federal Tax Service for the Oktyabrsky District of Penza

Registration with the FIU

Registration number 068004034545 dated March 22, 2019

Office of the Pension Fund of the Russian Federation for the Pervomaisky district of Penza

Registration in the FSS

Registration number 580073895958001 dated March 22, 2019

State institution – Penza regional branch of the Social Insurance Fund of the Russian Federation

Belyaev Dmitry Andreevich TIN 638102253106 from 20. 03.2019

100%

46.73	Wholesale of timber, building materials and sanitary equipment BASIC
43.29	Other construction and installation works
41.20	Construction of residential and non-residential buildings
16.23	Manufacture of other wooden building structures and joinery
23.69	Manufacture of other articles of plaster, concrete or cement
43.21	Electrical installation work
23.99	Manufacture of other non-metallic mineral products n.e.c.
16.29.1	Manufacture of other wood products

+ 34 more

Financial statements of LEPNOY DOM LLC according to the data of the Federal Tax Service and Rosstat for 2017–2021

Financial results for 2021

Revenue	Net profit	Capital
1. 3 million ₽ 10%	9 thousand ₽ 98%	348 thousand ₽ 3%

Accounting statements for all available periods

---

Financial indicators for 2021

• Coefficient of autonomy (financial independence)
  0.77
• Working capital ratio

  —

• Investment coverage ratio
  0. 77
• Current liquidity ratio
  —
• Quick liquidity ratio

  —

• Absolute liquidity ratio
  —
• Profitability of sales
  0. 7%
• Return on assets

  2.0%

• Return on equity
  2.6%

Comparative financial analysis for 2021NEW

Paid LEPNOY DOM LLC – TIN 5837075554 – taxes and fees for 2020

Insurance and other mandatory pension insurance contributions credited to the Pension Fund of the Russian Federation	3.4 thousand ₽
Insurance premiums for compulsory health insurance of the working population credited to the budget of the Federal Compulsory Medical Insurance Fund	796. 9 ₽
Insurance premiums for compulsory social insurance in case of temporary disability and maternity	453.2 ₽
Tax levied in connection with the application of the simplified taxation system	37.7 thousand rubles
Total	42.4 thousand rubles

According to the Federal Tax Service, the average number of employees for 2021 is
1 person

2020

1 person

1.3 thousand ₽

The values ​​are calculated automatically based on information about contributions to the compulsory medical insurance fund and the average headcount of LEPNOY DOM LLC, this information may be inaccurate

	03/20/2019 Registration of a legal entity
	Assigned to OGRN 1195835006597
	03/22/2019 Registration with the FIU, registration number 068004034545 assigned Office of the Pension Fund of the Russian Federation for the Pervomaisky district of Penza
	Registration in the FSS, assigned registration number 580073895958001 State institution – Penza regional branch of the Social Insurance Fund of the Russian Federation
	04/10/2019 Registration in the Unified Register of Small and Medium Business Entities
	03/05/2020 Financial statements for 2019 submitted
	04/10/2020 Legal address changed from 440068, Penza region, Penza, st. Categories Bathroom Floor Home Kitchen Miscellaneous Roof Tree Wall Window Scroll Up