Silicone injection damp proofing: Proofing – Wacker Chemie AG

SILICONE DAMP-COURSE

SILICONE
DAMP-COURSE
Gravity
or Pressure? | Ab-Tech Liquid | Specification | Other Liquids

We drill a series of holes along the base of an affected wall
and apply sufficient Ab-Tech Damp Proofing Liquid into
the holes by gravity feed. This produces a continuous band of
silicone damp-course where needed.

The liquid is free-flowing and soaks the fine pore structure
of the mortar and base masonry. The silicone component of the
siloxane liquid cures to form a band of moisture-repellent plastic
damp-course, inside the wall material itself.

We then patch the holes with matching mortar or plaster and
clean up to finish the job neatly and tidily. The holes are concealed
to blend in with the existing walls.

HISTORY

Chemical injection of walls to create a damp-course is a technique
that was developed in Europe in the 1960’s and has been used there
successfully since then. Modern siloxane damp-proofing liquid
is a further improvement.

GRAVITY FEED or
PRESSURE INJECTION?

It does not matter how the damp-proofing liquid is put into
the wall. There is no Australian Standard covering the topic,
however, the British Standard for the “Installation
of Chemical Damp-Proof Courses” allows several rational
methods, either low pressure injection, high pressure injection
or gravity feed.

The important factors are that the operator uses sufficient
liquid and applies it correctly to allow it to soak fully across
and along the wall to create a continuous silicone damp-course.

We use gravity feed injection in all types of walls. Based
on our experience, we apply a generous rate of Ab-Tech damp-proofing
liquid to ensure that a broad continuous layer of silicone damp-course
is created in the wall. To achieve this, we apply small quantities
of the damp proofing liquid directly into each of the the drilled
holes, without any pressure, allow it to soak in and repeat until
the recommended total application
rate quantity is attained.

The close spacing of holes and the repeated application of
small doses of liquid ensures that the treatment disperses reasonably
evenly throughout the target layer in the wall. If there are voids
in the wall the liquid will pool in bottom of such holes and soak
into the adjoining masonry. Particularly, the old mortar is very
porous and will absorb the liquid on contact and help it disperse
through the wall by natural capillary action.

Application Rates

AB-TECH DAMP PROOFING
LIQUID

Ab-Tech Damp Proofing Liquid is a high purity alkyl-silicone
(siloxane-silane), diluted in a user-friendly low odour petroleum
solvent, in a ready-to-use form. The components have a small molecular
structure that allows the liquid to soak deeply into masonry materials
by capillary action, and carry the water-repellent properties
into even the smallest pore space.

After application, the solvent slowly evaporates and the silicone
component chemically reacts with natural moisture to form a water-repellent
silicone plastic layer throughout the wall. The residual silicone
is inert, resistant to salts and alkalis and is non-toxic after
curing.

TYPICAL PROPERTIES:

highly water-repellent siloxane formulation

residual silicone is inert, for long life

low-odour formulation and non-toxic after curing

deep penetration into porous masonry

can be applied to slightly damp masonry

surfaces remain porous and able to “breathe”

clear liquid that cures to a clear, tack-free dry
surface

non-aggressive petroleum solvent, is safe to use

not Dangerous Goods according to the Australian Code

Ab-Tech Damp Proofing Liquid is blended and packaged
in South Australia. The component chemicals have been selected
to provide the most effective damp-proofing and to be as safe
and user-friendly as we can achieve. The liquid has little odour
and is not aggressive to materials and finishes. The formulation
avoids the dangerous and harmful types of solvents.

OTHER INJECTION LIQUIDS

Rising damp in South Australia activates salts in the walls.
Our siloxane liquid has been developed to resist such salts and
is the best material available for such conditions. Some cheaper
silicones and older technology liquids such as stearates and siliconates
do not have the same degree of salt resistance.

We use expensive solvent in our liquid that is the safest available
and has the least smell. Beware that there are cheaper liquids
available with harmful solvents that smell bad.

SAFETY:

We use high flash point petroleum components that have a reduced
fire risk compared with flammable petroleum liquid. Our product
is rated as Combustible Liquid and is not classified as Dangerous
Goods according to the Australian Dangerous Goods Code. However,
there are still risks and users should observe the Safety Precautions
printed on each can of our product.

SALT DAMP SHOP,
Adelaide, South Australia
home | videos
| about salt damp | silicone
| do it yourself

Damp Proof Injection | Damp Proofing Course Solutions

Home / Property Preservation / Damp Proof Injection

Posted May 12, 2020
|
in Property Preservation

Damp proof injection is a fast, cost-efficient and highly effective form of rising damp treatment. It is commonly used as a remedial damp proof course on buildings where the existing DPC has failed due to age or deterioration. DPC injection is designed to seep into the brickwork in order to prevent moisture from the ground rising up through the bricks by capillary action and causing rising damp.

What is a Damp Proof Course?

A Damp Proof Course, or DPC for short, is a barrier that stops damp from the ground rising up into a building. There are two main types of DPC: membrane damp proofing and chemical damp proofing.

Membrane damp proofing is essentially an impervious barrier which is laid along the bottom brickwork at least 150mm above the ground level during the construction of a house. Chemical damp proofing is usually a remedial DPC, meaning it is introduced by damp proofing specialists when the original DPC fails.

Damp proof injection refers to the installation of chemical damp proofing along the base of the walls of a building that is suffering from rising damp. While it does not form a physical barrier like membrane damp proofing, it lines the pores of the masonry wall with a silicone resin water repellent.

How Do Damp Proof Injection Creams Work?

Damp proof creams are scientifically formulated to penetrate deep inside the building material. They have a consistency that allows the active ingredient, silane, to be absorbed into the substrate both vertically and horizontally without running out. The silane then lines the capillaries before curing to create a water repellent barrier.

The type of chemical damp proof course that should be used is dependent on the wall construction and aqueous based fluid DPC’s may be injected by using high-pressure and low-pressure techniques instead of using DPC creams. Chemical injection DPC is usually used for brick or stone buildings, and our experienced surveyors know exactly how to recommend the most suitable remedial action.

Damp Proof Treatment Using Injections

After our initial survey, our technicians will get to work preparing the affected area both internally and externally before the damp injection begins. This may involve removing fixtures and fittings such as skirting boards and radiators to provide access.

If your property is suffering from rising damp, then any salt contaminated plaster will need removed before injecting a damp proof course. Plaster is usually removed to a height of no less than one metre to remove the salt affected plaster prior to injecting the chemical DPC.

Small holes (around 12mm) will then be drilled horizontally into the wall mortar joint to a depth of around 20 – 30mm from the full thickness of the wall, and the damp proof course will be injected into the boreholes. Left in the wall, the injected chemicals will penetrate the masonry surrounding the borehole. The cream then gets to work creating a water-repelling barrier.

After the damp proof injection, our team will re-plaster internally. Our specific re-plastering materials will ensure that any residual salts in the masonry do not affect the new plaster. This chemical damp proofing solution will provide you with a minimum of 30 years of damp free walls in your property, with the issue of our 30 year guarantee for your peace of mind and also the work can be backed up by the independent GPI guarantee insurance scheme if required.

Damp Survey

When damp appears in your property, you need an experienced damp specialist to accurately diagnose the cause of the problem and provide the most appropriate repair specification. Failure to properly diagnose a damp related problem can result in unnecessary repairs and further costly damage.

Our Surveyors are qualified to CSRT standard (Certificate Surveyor in Remedial Treatment) and experienced in all types of damp issues that could affect your property. With over 85 years’ experience in property preservation, we have the experience and knowledge to tackle any property damp problem you might have, with industry-leading guarantees that are backed up by protection insurance schemes.

This website uses cookies to ensure you get the best experience on our website. Read our Privacy Policy Settings Accept Cookies

Injection waterproofing: works, materials, prices

Injection waterproofing: how and where to apply

Injection waterproofing is a new technology that is widely used to strengthen and insulate the foundations of new buildings and existing construction projects. An effective way to create a reliable waterproof membrane between structures and aggressive environments.

In the article we will consider the waterproofing of objects by the injection method, the features of the technology, how the work is done, what is required for them, as well as its advantages and disadvantages.

What is injection waterproofing?

Injectable waterproofing is a waterproofing based on liquid polymers, pumped under pressure and works directly inside the building structure or in specially organized sections provided to minimize the consumption of the injection composition and the possibility of localizing leakage.

After entering the structure, helium polymer compositions polymerize, as a rule, within an hour, after which they acquire the ability to withstand very high pressure of the environment.

Application

The method of injection waterproofing has long been used in foreign countries. In Russia, this unique technology has appeared recently, but has already gained popularity in the construction and repair industry.

This technique involves pumping waterproofing compounds into the foundation material and other building elements that are subject to destruction under the influence of a humid environment. For insulation work, special materials and equipment will be required.

The main purpose of injection waterproofing is to strengthen and protect the foundation from destruction provoked by a humid environment. This method is relevant for increasing the bearing capacity of the foundation, for fixing the soil and sealing the formed cracks.

Modern technology is also used to eliminate the inflow of water formed in the foundation, and to equip the cut-off waterproofing between the foundation and the wall of the building.

Technology

Injection waterproofing is performed using a special technology. All materials used remain liquid for 30-40 minutes. Their hardening is regulated by the catalysts included in the composition. Experts recommend that work be carried out at a temperature not lower than 5 degrees.

Waterproofing injection methods

The choice of injection waterproofing technique depends on the selected material and the surface to be isolated.

Where the technology is applied:

For foundation injection. The best option is the use of a cement-sand composition based on silicates.
For waterproofing walls during the construction phase and during major repairs. It is recommended to use acrylic or polyurethane material.
For grouting basements and basements.
In order to strengthen the base of concrete structures, waterproofing of joints and cracks is carried out.
To improve the quality of a brick building, waterproofing is carried out by injection using hydrophobic compounds.
For strengthening old foundations and restoring bearing capacity.
For sealing cold joints in reinforced concrete structures, etc.

Methods for applying injection waterproofing:

“Gravity” – involves filling holes drilled at an angle with material and its subsequent movement under the action of gravity. When performing insulation by this method, fast-hardening compounds cannot be used.
“Under pressure” – filling of materials occurs under a pressure impulse. The pressure supply is provided by a pressure pump. It is possible to carry out work on this technology only in warm weather (not lower than 5 degrees Celsius).

Equipment for injection waterproofing

To carry out waterproofing work using the injection method, you will need a special metal packer and a high-pressure pump.

Materials

Injection waterproofing of the foundation and other building surfaces is carried out using various materials.

What materials can be used:

Polyurethane polymer is a highly plastic material that can withstand various loads well. Economic consumption. Affordable cost. It is widely used to isolate foundations located on the territory of quicksand and loose soil.
Acrylic gel is a strong and resistant material. Easily penetrates into the smallest pores of the foundation. Hardens quickly. Soil particles are used to strengthen the material, which provides additional protection against washout.
Epoxy material – used in dry construction. Hardens quickly on contact with air. After complete polymerization, the solid membrane becomes completely impermeable to water.
Materials based on siloxanes or silicates. When interacting with the main building material, they are converted into an emulsion that creates a highly effective barrier to water. Can be used for waterproofing surfaces with high humidity.

Work steps

Waterproofing works by the injection method are carried out in stages, in accordance with important technological rules.

Stages:

Examination of the surface to identify points of localization of moisture penetration.
Drilling through holes in increments of up to 0.5 m. Diameter – up to 20 mm. Additional holes are made in places of localization.
Drilling blind holes along a fault line or cracks.
Metal packers are inserted into the created holes, ball valves are fixed to their outer part.
A tank with a waterproofing compound is connected to the ends of the fixed taps.
The composition is transported through the tube by gravity or under the influence of pressure (depending on the chosen method of injection).
After the material has hardened, the tubes are removed.
The outer surface is covered with a layer of moisture-resistant plaster or cement-sand mortar.

Advantages and disadvantages

Injection waterproofing has many advantages. This technique eliminates the need for earthworks when strengthening the foundation of ready-made buildings. The mixtures used do not contain harmful impurities, therefore they are absolutely safe for the human body.

Due to the low density of the compositions, a high penetrating ability of the material is ensured. When carrying out work, it is not necessary to carry out preliminary drying, injection gels have good adhesion to wet surfaces. Waterproofing can be performed even in cold weather, the main thing is to choose the appropriate material adapted to low temperatures.

Other advantages of injection waterproofing:

work can be carried out during the construction phase and after the construction of the building;
technology is used for overhaul;
the result is a guaranteed quality waterproofing with a reliable membrane that envelops the entire surface.

The disadvantages of injection waterproofing include the high cost of materials, the need to use special equipment and the mandatory observance of technological rules. In the absence of skills, it is better to entrust this work to specialists.

Features of injection of various designs

Injection waterproofing is carried out according to the standard scheme, but has some features when performing work on different construction sites.

To improve the performance of the erected building, walls are injected. Works are carried out at the construction stage or during the overhaul.

When the foundation is injected, vertical waterproofing is performed with the creation of a horizontal barrier that prevents the penetration of moisture.

External and internal waterproofing is carried out when injecting basements.

To strengthen the foundations of concrete structures, waterproofing of cold and moving joints is carried out.

To increase the strength and moisture resistance of brick buildings, insulation is made using hydrophobic compounds.

To date, high-quality injection waterproofing is performed by specially trained craftsmen who have all the necessary equipment in their arsenal.

Injectable waterproofing

The purpose of waterproofing a building and structure is to maintain the strength of the foundation, and, consequently, of the entire structure as a whole, extending its service life and minimizing possible repair costs.

Usually a protective waterproofing layer is created during the construction process. But, it often happens when the owner of the premises acquires it in the state when you have to think about updating the waterproofing. What to do in this case?

The most promising option is to expose the foundation and re-engage in the creation of a protective layer.

The method of such work is always chosen individually, based on the characteristics of the building and the causes of insulation failure. Applying a new waterproofing material to the foundation is not so difficult and costly as it seems. But, here the manipulations with the soil require large time and financial investments. And the subsequent need to improve the territory makes the project even more expensive.

The way out of this situation is the method of injection waterproofing. It gained great popularity in the countries of Western Europe, where they learned to protect buildings from water and moisture at any time of the year. Moreover, this method allows you to work indoors.

Work technology

Before the start of waterproofing work by injection, an inspection of the object is carried out and a detailed plan of the necessary operations is drawn up. This work must be entrusted to experienced specialists who will correctly identify the problem by determining what substance is required to treat the underground part of the structure, and calculate the volume of polymers.

Depending on the density of concrete and the goal, the type of composition of the injection solution is determined. In this case, the introduction of injection polymers can be carried out directly into the body of the building structure, as well as into seams, cracks in the foundation. If necessary, the solution is also supplied behind the structure of the structure, thereby creating a protective screen. If you do a complete waterproofing of the object, you will need a large amount of solution. It will be more economical to fill them with only cracks and seams. However, the possibility of this should be determined by specialists.

The waterproofing plan must have a diagram indicating the number and location of holes, each of which has its own number. Holes, or small holes, are drilled in a checkerboard pattern in increments of 25-30 cm. Their depth should be approximately 70% of the wall thickness. Through holes are drilled only to create a waterproofing filter surfaces.

To restore the waterproofing of the horizontal layer, the holes are made in two rows at the level of the beginning of the wall. In the holes obtained, parquets are attached, through which an injection solution is injected using special equipment capable of creating a pressure of 250 atmospheres. Then all accessories are removed, and the surface of the wall and foundation is cleaned of excess mortar. The next stage of finishing work is recommended to begin with covering the restored area with a special sealant. This will make it possible to level the traces of repair and improve the hydroprotection of the surface of the material.

Types of injectables

Today, a variety of innovative compounds are used to create injection waterproofing, and their list is constantly updated. But, the most popular are polymer solutions.

Depending on their chemical composition, they can have different elasticity, porosity, the ability to increase in volume and polymerize. The ability of polymer solutions to fill microcracks and other voids is based on the property of polyurethane to expand several tens of times under the influence of moisture. In addition, such compositions are well retained on the surface of almost all types of materials.

Polyurethane injection solutions are used for:

fix stubborn leaks;
insulation of working seams and damaged structural butt joints;
horizontal waterproofing;
filling voids in the foundation;
foundation strengthening;
structural reinforcement.

To repair materials with a finely porous structure, as well as to eliminate cracks and protect the separating layers of the foundation from water, epoxy and polyurethane resins are used. They are very strong, have good adhesion to concrete, steel and other materials that may be included in the foundation structure. This resin is not used in working with PVC, polyester and polyethylene. The main purpose of epoxy resins is to strengthen small damaged areas of the waterproofing of an object.

In some cases, instead of polymers, acrylate gels can be used, which can include up to five different components. Acrylates do not have a high degree of viscosity. However, they perfectly penetrate the structure of the material, filling the smallest pores and voids. At the same time, such gels are elastic and ideally fit on building structures. The injected acrylate is in a gel state. It expands and solidifies only upon contact with water. Such an injectable composition is suitable for repairing active leaks, as well as for restoring waterproofing and creating new barriers.

Silicone compounds are used to create waterproofing and strengthen old foundations. They are made of silicone and silicon. Such compounds have high adhesion and well fill micropores, cracks and other voids. It is possible to strengthen the foundation and soil with the help of microcements.

Difficulty of choice

Before starting waterproofing work, the question always arises, which composition and solution is best suited for injection. Only a specialist can answer it correctly. But, the general principles of choice are as follows:

To create masonry waterproofing over large areas, mortars with low viscosity and a long curing period are suitable. At the same time, the composition penetrates better into the brickwork and fills the pores of the building material.
Cold working joints of foundations and walls are recommended to be treated with acrylic gels.
Communications bushings are protected with polymer resins.

In addition to creating an insulating film, cracks can be repaired using injection waterproofing.