Tv brick wall mount: How to Mount a TV on Brick Wall

How to Mount a TV to a Brick Wall

Have you considered mounting your TV to a brick wall in your home? While this is certainly possible, it does require some extra preparations and a few extra tools to get it right. So how do you go about mounting the TV?

First, finalize the placement of your TV. Mark the holes precisely with the bracket and start drilling using masonry drill bits. Hole sizes should match the length of the screws. Fix the brackets with washers and screws. Add the bracket to your TV and hang its hook on the wall bracket.

If that sounds too intimidating, you can also use non-drilling options to mount your TV, such as adhesives or rails. Let’s look at how to mount a TV to a brick wall with and without a drill.

Can You Mount a TV to a Brick Wall?

You can mount a TV to a brick wall, but it’s a slightly different process from mounting on a regular wall. The job requires some extra drilling. Also, you must make holes in the brick and not the mortar, which can be a flimsy option.

The good news is that most of the setup process is the same as the process for mounting on drywall. With some caution and patience, you can easily secure the mount of your TV to a brick wall.

What Do I Need to Mount a TV to a Brick Wall?

Mounting a TV to a brick wall is a little more challenging than installing your device onto drywall. Therefore, you might need some extra things to make sure the bracket is strongly fixed.

TV Bracket

When mounting your TV to a wall, you actually install a TV bracket (on Amazon) first. This holds the weight of your TV, so it must be installed securely.

Please note these brackets are available in different sizes, depending on your TV panel. Therefore, you must pick the one that supports your TV’s particular frame size.

Also, you can choose between diverse designs. Some are fixed, while others, such as the Mounting Dream Wall Mount (on Amazon), can help rotate your unit’s screen at different angles.

A Drill Machine

Most drills are fine for this job. However, a cordless drill will make things much easier, especially if it’s one with a hammer function, the one with a hammer function, like the DEWALT 20V Max (on Amazon). This is because you will be required to switch to the hammer function when finishing the holes.

It’s important not to overdo the holes. These must be precise and drilled as long as needed. Hence, you might like to conclude the job using a hammer and not a power drill.

Note: Be wary of the impact driver. These are fast and can end up over-tightening the screws.

Masonry Drill Bits

You can’t miss this must-have tool when drilling on brick walls. These feature chisel-like tips along with wings on the sides to ease the drilling process when working with hard surfaces such as brick, concrete, etc.

Usually, most of the fastener kits included with the power drill have masonry drill bits, so you won’t have to purchase them separately.

Anchors Screws

If your TV seems heavier than most, hanging the brackets using concrete screws is a much safer option than with plastic anchors. Typically, a TV weighing over 75 pounds will require anchor screws.

Although plastic wall anchors can hold lighter TVs, it’s better to use anchors on a brick wall.  

Further, to secure your screws, you should use a drill bit (on Amazon).


These come into play when you find the slots on the mounting hardware to be a bit larger than the head of the screw. Make sure to choose the right size washers. Otherwise, they won’t do the job as planned.

Measurement Tape

No one likes to make mistakes when drilling and having to redo the holes. This is time-consuming and ends up covering the wall with unwanted holes. You must keep a good measuring tape (on Amazon) handy.

Finalizing your placement will become much simpler this way.


A good hammer (on Amazon) is a very basic tool every household has. Use it to push the anchors farther into the bricks for a stronger hold. Alternatively, you can also use a rubber mallet (on Amazon).

A Marker

It is easy to mark on a painted wall since most of the marking tools work fine on drywalls. Sadly, that is not true for brick walls. Therefore, you must use a permanent marker to set the drill sites.

Other Gear

Apart from the basic tools, it’s recommended to get some other gear as well, such as small shop vac (on Amazon) to hold the excess dust resulting from drilling brick walls. Safety glasses (on Amazon) with a dust mask to protect your eyes and lungs from the dust are also key.

In the end, you can also use a level (on Amazon) to make sure that the bracket is aligned perfectly to the wall edges.

Mounting a TV to Your Brick Wall: Step-by-Step Guide

With just a little extra drilling, the process remains almost the same for mounting a TV on a brick wall as it is for the drywall.

Follow the step-by-step guide to install your TV unit onto a brick wall:

Step 1: Finalize the Location and Placement

You don’t want to have to keep moving your TV once it’s been mounted. So, why not finalize the location and placement beforehand? You must consider a few things when choosing the location:

  • The chosen location must have an electric socket close by, or you may have to get a wire extension. While this isn’t a problem, it might not be the look you’re going for.
  • Usually, the center of the wall looks ideal for hanging your TV. However, if you have an unusual setup, you might want to ditch that idea and consider other positions.
  • Determining the height of the TV from the floor is a crucial part of perfecting the TV installation. When sitting on the couch, you should feel comfortable watching videos. That said, consider the distance of your sitting arrangements from the wall to calculate the TV’s height from the floor.
  • You can perfect the alignment with the help of the level.
  • Mark the holes carefully. To do so, place the bracket on the wall and use the marker to fix where you will be drilling holes.
  • Try to mount on bricks and not mortar. Although it might seem strong enough, the holes in the mortar become flimsy with time. This may lead to accidents such as brackets falling off the wall.

Step 2: Make Sure Safety Precautions Are in Place

Wear your mask and dust glasses before you start drilling. This will protect you from dust and keep your lungs and eyes safe.

Step 3: Complete the Drilling

As explained before, drilling is a bit different when it’s the brick wall instead of the drywall.

Now that you have already marked the places where you want to make holes, all you need for this step is the drilling tools.

Just remember, unlike mortar, bricks are pretty tough to drill into. Hence, always double-check the hole position and alignments using the level. For any change, just change the marking and check again.  

When drilling, you will need special masonry drill bits. Make sure to use the hammer drill to prepare holes in marked positions. Also, never forget to keep the hole lengths just as long as the screws.

Step 4: Fix the Bracket on the Wall

Place the bracket on the brick wall, aligned with the drilled holes. Use washers to ensure that the screws are tightly fixed on the bracket. Tighten one screw at a time and follow others one by one.

Step 5: Connect Remaining Bracket Set to the TV

Some parts of the bracket will connect to the TV. All the screws and washers needed to complete the job are usually packed with the bracket.

Use the same tools to fix the bracket to the TV. However, never tighten the screws too much. Doing so can damage your device.

Step 6: Mount Your TV

This is the final step, and you might need some help if the unit is too big. While you hold the TV to hang it on the fixed bracket on the wall, you also need to connect the wires that go behind the unit.

For this reason, asking for help is a wise decision. Make your connection to the back of the TV and hang it on the bracket on the wall.

Once setup is completed, verify if the alignment of the TV hook on the edge of the wall’s bracket is secure before letting go of your device.

No-Drilling Alternatives

Sometimes drilling does not seem like a feasible option on a brick wall. Also, there are times when individuals don’t want to destroy their walls with holes.  

Thankfully, there is a way out for people looking for no-drilling alternatives for mounting their TVs.

TV Stands With Mounts

The simplest way to ditch making holes on the brick wall is to get a TV stand with mounts (on Amazon). This way, instead of fixing brackets on the walls, you can just mount your TV on the stand.

Most of these stands feature extra shelves to adjust devices that you want to connect with your TVs, such as an AV system or an Xbox.


This might not seem like a safe option. However, very strong adhesives (on Amazon) can help you avoid drilling. At the same time, you must consult someone experienced about how well the adhesive will carry your unit’s load.

Remember, this option is a lot riskier if the brick wall is not even. That said, you must consider all the pros and cons of strong adhesives before making a decision.


Often used for picture hanging, rails can also be a suitable option for hanging your TV without drilling. However, you will require adhesives to stick the rails on the wall. And as it’s the case with the adhesive option, a rail isn’t the safest choice.

Brick Clamps

Depending on the weight of your TV, you will require a certain number of brick clamps (on Amazon) to secure your TV on the brick wall. Make sure to purchase these after measuring the mortar’s depth so that they cling to the brick edges tightly.

Tips for Keeping Your TV Outdoors

If you’re getting a new TV for your living room, how about installing the old one outside? The good news is that it is possible to mount your TV outside. But at the same time, you need to take extra care to keep the TV safe.

Here are the tips that will help you secure your TV’s installation outside.

Frame Inside the Enclosure

When putting your TV outside, where it won’t be visible at all times, consider using an enclosure. IP-rated enclosures protect your unit from dirt, heat, water, and even thieves.

In addition to covering the TV, make sure to cover your AV accessories inside the enclosure for protection against harsh weather conditions.

This way, you can sleep easily, even with your device out in the elements.

Never Forget the Shades

Your TV isn’t waterproof. Always find some sort of shelter for your outdoor TV.

Keep in mind that rain doesn’t always fall straight down, and winds can push rain in all directions.

Connect the TV to an IP-Rated PowerPoint

Usually, when installing sockets outside, electricians make use of IP-rated PowerPoints for safety against the weather. If yours isn’t the same, get one installed first.

Make sure the one you get has a cover with room to insert the cord into the socket.

Avoid Direct Sunlight

Sunlight can affect your screen clarity. The brighter the sunlight, the more difficult it is to achieve optimal viewing. If you can’t avoid the sun, try a high-brightness panel instead.

Alternatively, install your TV’s back facing the sun towards the south. Setting the unit in the opposite direction would expose the LCD panel to direct sunlight, making it hard to watch TV.

Use a CAT Cable Over HDMI

HDMI cables can only carry signals short distances. Hence, if you are looking to connect your TV to other devices placed around the house, HDMI just won’t cut it.

That’s when you can use CAT5 or 6 cables instead of an HDMI cable. These can run long distances without destroying the signal quality. However, you will need an HDMI to CAT converter to make the signals compatible.

How to Mount a TV on a Brick Wall

If you have ever mounted a TV on a typical wall (drywall on wood studs), you know it’s not that difficult. The most important things are making sure the screws are going into the studs, and that the mounting bracket is level.

But what do you do when you want to mount a TV on a brick wall? It’s basically the same concept, but you don’t have to worry about hitting the studs, and there is a little more drilling involved.

I recently mounted a TV on the brick chimney on our back porch. So I thought I would document the process and show you how I did it.

Here’s what you’ll need:

  • Hammer Drill
  • Level
  • 3/16″ Masonry Drill Bit
  • Impact Driver
  • 1/4″ Masonry Screws

Step 1: Determine the Placement

Unless you have a unique set up, you normally want to mount a TV in the center of the wall horizontally. I measure the width of my brick chimney to find the center point and made a mark. But what about the height? Here are the recommended heights you should mount a TV based on size:

TV Size Height from floor to TV Center
42″ 56″
55″ 61″
65″ 65″
70″ 67″

Another thing to consider when mounting your TV is the location of the power outlet. I like to mount my TV so that the outlet is near the top of the TV. That way the TV can be tilted down some without the power plug interfering with the amount of tilt.

Step 2: Drill Holes

Now that you have determined exactly where you want to place the TV, it’s time to drill the holes. As mentioned above, this is where the process is different than mounting a TV on a standard framed plus drywall wall.

I held my mounting bracket in place and then used a pencil to mark on the brick where I wanted to drill the holes.

Since mortar is a little easier to drill than brick, I made sure to line my holes up with a horizontal mortar joint.

Using the horizontal mortar joint got me really close to level. But then I took a level and laid it across both marks to double-check. If they are off a little, simply adjust and make a new mark.

When you are drilling a hole in brick, you need to use a special masonry drill bit. For this project, I used a 3/16″ Tapcon bit.

Next, I used the hammer drill to drill my holes on each mark. You only need to drill as deep as the screws are long.

Step 3: Fasten with Screws

Once I had all four holes drilled, I held the mounting bracket in place against the brick. I added a washer to the first screw and drove it into the drilled hole.

Then I followed with the three remaining screws adding washers to each.

Step 4: Add the Brackets to the TV

This step is pretty straight forward. Using the supplied screws and washers, I added the two mounting brackets to the back of the TV. Be careful not to over tighten the screws. Doing so might damage the TV.

Step 5: Hang the TV

This is where you might need some help. Find someone to help you hold the TV while you connect the wires, or vice versa. Then both of you lift the TV up so that the mounting brackets hook over the top edge of the wall mount. Before turning lose of the TV, double check to make sure that the brackets are securely in place.

How to mount the TV bracket on different types of walls?

The most secure option is to attach the bracket to a load-bearing wall. It is capable of withstanding heavy loads and will definitely provide the TV with the right foundation, and it will protect you from unnecessary expenses to replace a fallen TV. But, unfortunately, it is not always possible to plan the space in such a way that the fasteners fall precisely on the supporting structure.

So you have to go with what you have, but don’t worry about giving up the bracket. Not at all! Fasteners can be correctly selected for lightweight walls. 9Brick;

  • Drywall;
  • Plaster;
  • Wood;
  • Concrete.
  • All these materials differ in their structure, filling, rigidity and vapor permeability properties. Also, the materials will differ in varying degrees of density, as a result, some of them may crumble during drilling.

    Let’s take a closer look at each type of wall and see how you can successfully hang even the heaviest TV on the walls.

    Concrete and brick

    These wall materials are considered the most reliable for mounting brackets. As a rule, even the installation kits already include the appropriate fasteners. Well, it’s worth saying that there are no special problems with mounting on these walls, with the exception of only a few nuances.

    The first thing to consider is the presence of armature, electric cable, gas pipeline, plumbing in the wall. It is very important to provide for these things so as not to accidentally damage the corresponding engineering elements of the apartment. It will be easiest for those who have a plan for laying certain systems, or you yourself know their location. Otherwise, you will have to act randomly.

    If the wall is covered with a smooth finishing material, apply masking tape in the area marked for the bracket to prevent the drill bit from slipping. Otherwise, there will be no problems with the installation. Choose in advance a suitable drill for a puncher, as well as dowels for installation.

    Gypsum plaster

    This material consists of a mixture of gypsum and mineral or organic substances. These are the same blocks from which non-load-bearing partitions are made in apartments. I must say that the material is now very popular in construction, so the owners of new buildings should understand how to work with this material.

    The most important point in installing the bracket on the plaster is the impossibility of using the fasteners included with the installation. They are not intended for crumbling material! Buy fasteners separately!

    It is best to use ordinary bolts with nuts with a diameter of 6-8 mm. And keep in mind that you will need access to the wall from the other side, because the bracket will be installed with through drilling.

    Through holes must be additionally fixed with PVA glue. Apply it to the hole made and install the bolts – the glue will additionally strengthen the wall at the drilling site and prevent it from crumbling. Wait for it to dry.

    After that, it is important to make a wider hole on the back of the wall according to the diameter of the nut, also do not forget about the washers under the nuts. In the future, you can hide the fasteners behind the plaster, and no one will guess about the presence of it. Also coat the new hole with glue. Well, then you can mount the bracket and TV.


    This material, it must be said, is almost not suitable for fastening any heavy types of equipment or objects. But to check it is real.

    It is important to say here that, as such, fasteners will not be mounted on drywall (the material will not withstand), but on a metal profile inside the plasterboard sheathing. So keep in mind that it is necessary to think over the mortgages for installing the bracket deeply in advance. Well, keep in mind that the reliability of such a wall leaves much to be desired and you should not install large TVs on it.

    At the planning stage of the room, it is necessary to provide for additional reinforcement of metal racks so that you can safely mount the equipment. In addition, choose special types of fasteners – drywall anchors or the so-called butterfly dowels.


    Natural material is less durable than the same concrete, but its advantage is that the thicker the beam, the more reliable the fastening will be.

    In fact, when mounting on a tree, the bracket can be used as a classic installation method, as well as through. But choose not complete fasteners, but self-tapping screws for wood with a length of at least 30 cm. Accordingly, for through fastening, select reliable and long bolts + provide holes for deepening nuts and washers.

    Perhaps mounting on a wooden wall is an exceptional case for country houses. In apartments, the choice falls on the previous options for partitions. Always take into account the weight of the TV, the diagonal of the screen, because this increases the load on the bracket and fasteners. It is also worth choosing the bracket itself more carefully. The wider the distance between the fasteners, the less the load on the wall! Good luck.


    How to properly hang a TV on the wall with and without a wall bracket

    If you have purchased a wall-mounted TV, then the question arises: how to hang it on the wall correctly? In general, there is nothing complicated in the installation of the device. If you know how to use a drill, hammer and screwdriver, then you can quite cope with this on your own. In order to mount a Samsung TV receiver or any other on the wall, special devices are used: properly hang the TV on special devices – brackets. They vary in shape, size and functionality.


    Advantages and Disadvantages of Hanging Your TV on the Wall

    If after purchase you cannot decide where to place the TV, then consider the advantages of hanging it on the wall.

    1. Aesthetics . Flat modern TV on the wall will decorate any room interior. It will not look out of place in almost any style of decorating a room, and in some cases can set the tone for the entire room.
    2. Availability . If there is no suitable furniture in the room where the TV will be located, then buying a bracket will cost significantly less than a cabinet.
    3. Security . If there are animals or children in the apartment, then it will be much more difficult for them to drop a TV screwed to the wall than standing on a cabinet or table.

    As with any solution, there are disadvantages to hanging a TV on the wall.

    1. Putting the TV on a cabinet or table is much easier than hanging it on the wall. In the second case, you will need a tool and the skill to work with it.
    2. Not every wall will do – it must be free of heating equipment.
    3. If it is decided to dismantle the TV, the mounting holes will have to be sealed.

    Types of brackets

    In order to choose the right bracket for your Samsung, LG or any other TV, you should study the characteristics of the device. It is important to know its diagonal, weight and VESA standard. This is the generally accepted distance between mounting holes, predetermined by the manufacturer. It varies from 10 * 10 to 40 * 40 cm. Based on this, a bracket is selected. They differ in the material of execution, the number of knees (their absence), a rotary / inclined / fixed platform, designed for different diagonals.

    Important! Most brackets can withstand weight up to 25 kg, and it is extremely difficult to find a modern TV with a weight greater than this value. However, to make sure that the mass of the device is still acceptable, it will not be superfluous.

    Let’s take a closer look at the design of the brackets.

    1. Fixed . Allows you to securely fix the device, but without the possibility of its rotation or tilt. This TV mount has a minimum of holes and is easy to install.
    2. Inclined. Often used when mounting a TV receiver high above eye level. To ensure comfortable viewing of TV, the mount allows you to tilt the panel at the desired angle.
    3. Tilt and turn. This mount is very convenient if you plan to mount the TV on the wall under the ceiling. Due to the rotary mechanism, TV viewing is possible from anywhere in the room.

    How to hang the TV

    Before you hang the TV on the wall with your own hands, it is important to determine the height of the unit. According to existing standards, the bottom edge of the device must be at a distance of 0. 7 m to 1 m from the floor. If the TV set will be bought for the kitchen, then its location under the ceiling will be the best option. However, there are other options for placing a TV in the kitchen.

    Don’t worry if the right spot is slightly above eye level – you can adjust the tilt of the using the tilt/swivel bracket. It is best to choose this one: it allows you to adjust the position of the device for maximum viewing comfort, and there will be room for wires in the back.

    Important installation instructions

    Start with study wall . It can be concrete, brick, wood or plasterboard. You shouldn’t mount TV on the last option – with a probability of 99% after a while it will tear out a piece of such a wall and break. Knowing the material from which the wall is made is also necessary to understand which drill will be needed to make holes. But you don’t need to worry about fasteners in order to fasten the bracket to the wall, and the TV to it – everything you need is included in the suspension and TV set.

    Important! When determining the location of the bracket on the wall, consider the presence of hidden wiring and the distance to the outlets. Also, do not forget that there should not be heaters nearby.

    Hanging the TV on the bracket

    In order not to rack your brains on how to hang the TV on the wall with the bracket, you need to follow some simple steps.

    1. Mark drilling points on the wall. To do this, use a tape measure to measure the distance from the holes for the bracket on the back of the device to its bottom edge. Then mark from the floor 1 m + the value obtained from the measurements on the TV. You will get the height at which 9 will be drilled0086 bottom mounting holes . Draw a line through this point using a level.
    2. Now attach the TV mount (wall) in such a way that the drawn line passes through the bottom holes of the hanger.
    3. The next step is to draw through the holes in the mounting points for drilling.
    4. Before installing the TV bracket on the prepared wall, in some cases it is necessary to check the installation site for concealed wiring (using a special tool). Using a drill (or better, a puncher), drill holes according to the marks made.
    5. Using a hammer, hammer in the dowels into the holes.
    6. Place the bracket against the wall and screw the bolts (in some cases self-tapping screws) into the driven plugs using a wrench.
    7. After the bracket is securely fixed, you can use the help of a third party to bring the device to the mount and hang it on it.

    Hanging TV without bracket

    Flat 42” TV panels (and especially larger units) are ready for installation without the use of special brackets. Device manufacturers have already provided for how to hang the TV on the wall without a bracket. For this, special “lugs” (grooves) were made on the rear panel of the device . Therefore, installing a TV with “ears” is not much different from hanging a picture or a mirror. The main thing is that the fasteners correspond to the weight of the device. If the ears for hanging are not provided, then you can make the fasteners with your own hands.

    How to hide the wires

    Having decided to hang the TV on the wall, the user will certainly think about how to hide the wires. Obviously, if they just stick out, then all the beauty of this installation method is nullified.

    Even at the repair stage, it is worth considering a place where the TV will stand in the future. It is advisable to place an electrical outlet and a socket for the antenna at the rear. It is better to do several of the first: you may have to connect a smart set-top box with external power or other equipment. If there is a cabinet under the TV, then some of the sockets can be mounted at a distance of 30 cm from the floor and a couple more directly behind the screen.

    Tip! It is quite difficult to predict in advance what exactly will be connected to the TV, so ideally you should take care of having 5-6 outlets. This amount is certainly enough for any devices that may be needed in the future.

    If the repair has already been done, the wiring box comes to the rescue. It can be neutral white or decorated in the colors of the interior. If there is a window nearby, then the cable can be hidden behind a curtain, the socket can be raised to the ceiling, and the wire to it can be put behind the eaves.

    Below are some interesting wire decorating ideas.

    Advice from the experts

    The advice below comes from service professionals who install and set up television equipment. Thanks to these recommendations, the risk of hanging the TV on the wall incorrectly is minimized.

    1. The selection of the bracket must be carried out taking into account the weight and diagonal of the TV.
    2. When choosing a bracket with swivel and tilt elements, make sure they are are made of metal. Even the highest quality plastic can deteriorate over time.
    3. When installing a TV in a niche, make sure that its dimensions have a margin of . Otherwise, air circulation may be disturbed, which may affect the service life of the TV.
    4. Installation is carried out as follows: first, the bracket is attached to the wall, then the removable platform is attached to the TV, and only after that both elements are connected to each other. The last step is connecting the wires.
    5. If the bracket has swivel or tilt mechanisms, then make sure to have a supply of wires – they must not be pulled or kinked in case of a change in the position of the device.

    Do-it-yourself bracket

    If you are not going to change its position during operation of the telly, then you can make a simple and inexpensive TV mount on the wall with your own hands.

    To mount a unit with a 32 or 42 inch screen, you will need to prepare 4 aluminum or steel corners (to be used in the manufacture of a TV bracket) and 1 spoke from a bicycle. It is recommended to use aluminum corner because it is easier to process. The dimensions of the segments are not important, the main thing is that the holes on the body of the device and on the corner match.

    1. Make 2 holes in the parts for attaching to the unit, and in the upper part – one for the knitting needle. Attach the finished parts to the body of the TV receiver (using M4 screws).
    2. The remaining pair of parts must be mounted on the wall. First, you need to drill 2 holes in them for fastening to the wall (or more, depending on the size of the diagonal of the device and its weight) and one hole in the upper part of the part for inserting a knitting needle.
    3. After that, markings are made on the wall through the holes made. All holes in the 4 parts must be located strictly opposite each other in order to avoid distortion of the device after installation.
    4. The distance between the corners should be slightly less than between the same parts on the unit so that the latter wrap around the wall corners from the outside (when placing the TV mount on the wall, it is recommended to use a building level to accurately position the parts horizontally).
    5. Now you can hang the TV on the wall. To do this, you need to lift your 42 inch unit and align the mounts as shown in the figure, after which you need to insert the spoke. If there is no knitting needle, it can be replaced with a nail with a hat. For heavier machines, use thicker nails, eg 100 mm long. At this stage, mounting the TV on the wall with your own hands is finished.

    Plastic dowels of the desired diameter and length (depending on the weight of the unit) can be used to fasten the parts to the wall.

    Before attaching the TV to the wall, you need to determine the width of the corners . It should be such as to ensure normal ventilation between the wall and the TV receiver. Otherwise, your 42 inch TV will overheat, which will affect its lifespan. All wires, electrical and antenna, can be hidden in the cable channel.

    Hanging a TV on a Plasterboard Wall

    There are many opinions on how to hang a TV on a plasterboard wall. Some say that you can use a butterfly dowel, others – that this is not a reliable mount. From practice, it has been noticed that TV sets weighing no more than 15 kg (diagonal 42 inches) can be hung on a “butterfly”. This option can be used for a 32 or 42-inch wall-mounted TV. Otherwise, for TVs with a larger mass, there is a risk of destruction of drywall. For clarity, how to use the butterfly dowel, you can watch the video:

    You can hang the TV on a drywall wall in a more reliable way: you should use a strong magnet to find the screws that fasten the sheet to the rails, and then attach the bracket to the metal profile. You can also hang the TV on a plasterboard wall using the stud screw.

    This anchor can be used as a fixing element in both concrete and brick walls (pre-drilling a hole of the desired diameter). The length of the stud must be selected taking into account the distance of the drywall sheet from the main wall. The deeper the anchor is screwed into the brick or concrete, the more weight it can withstand, since the entire load will be on the load-bearing wall, and not on the facing sheet.

    How to mount the TV on the wall was discussed above. But what if the drywall sheet is used not as a cladding, but as a partition? Attaching an expensive device to such a plane is highly discouraged. In this case, the TV can be installed on the special stand shown in the figure below. A TV hung on a bracket in this way can be rotated in any direction (thanks to the rollers on the stand), that is, the entire structure becomes mobile.

    Can be used to mount the TV to a plasterboard wall by screwing pipes to it to install the bracket.

    Another option on how to properly hang the TV on an unstable wall can be using a strip and chipboard , which can be well fixed on it. And already on the strip, you can attach shelves, a bracket and install the device.