How to hide cable wire on wall: 5 Brilliant Ways to Hide Wires in a Room Without Going Into the Walls

5 Brilliant Ways to Hide Wires in a Room Without Going Into the Walls

Conceal that unsightly wire without hard labor!


Family Handyman

Tuck Speaker/Low-Voltage Wire Between Carpet and Baseboard

Before you invest in any products, if there’s room you can tuck speaker wire between the carpet and the baseboard in a room with wall-to-wall carpet. To do this, you can simply use a ruler or paint stir stick to force the wire out of sight.

Here’s more on the tip, plus additional wire hiding information.


Family Handyman

Install Plastic Raceways

If you can’t simply hide low-voltage wire under rugs and behind furniture, try using plastic raceways along the trim. You’ll find them in various shapes and sizes to work with the length and width of your wires. You can paint the raceway to match the wall or trim.

Here’s how to add outlets safely with surface wiring.


Family Handyman

Invisible Wire Clamps

To conceal wire around a door, DIY your own wire clamps using a clear plastic soda bottle. To do this, simply cut the bottle into 1-1/2 x 1-in. strips, then loosen the trim with a small pry bar, wrap the plastic around the wire, and slide it between the wall and trim.

New to projects involving electricity? Don’t make these 10 beginner’s mistakes.


Sewell Direct

Run Ghost Wire Along Wall

Sewell Direct offers “Ghost Wire” that’s a spool of 16 AWG speaker wire, about the width and thickness of duct tape. It has a strong adhesive on one side, so it can be easily run along walls, floors and under carpets. This invisible wire solution is a non-invasive and low-cost alternative to cutting holes in the wall. Check out Sewell Direct’s guide, which covers ghost wire, super flat adhesive speaker wire and a ghost wire terminal block.

Here’s how to install low-voltage outdoor lighting without wires showing.

Photo: Courtesy of Sewell Direct



Hide Wires Inside a Shower Curtain Rod Cover

If you’re mounting your TV to the wall and don’t want to install the wires inside the wall, you can hide the clutter with a shower curtain rod cover. You’ll want to lightly sand the cover, then paint it the same color as your wall. Fresh Crush has the DIY how-to steps.

You may also enjoy these 25 uses for tension rods (other than for hanging a shower curtain!).

Photo: Courtesy of Zenith

Originally Published: July 18, 2018

Alexa Erickson

Alexa is an experienced lifestyle and news writer, currently working with Reader’s Digest, Shape Magazine and various other publications. She loves writing about her travels, health, wellness, home decor, food and drink, fashion, beauty and scientific news. Follow her traveling adventures on Instagram: @living_by_lex, send her a message: [email protected] and check out her website:

10 easy steps to hide TV wires in the wall – in less than an hour

Join our newsletter

Get the best home decor ideas, DIY advice and project inspiration straight to your inbox!

Thank you for signing up to Realhomes. You will receive a verification email shortly.

There was a problem. Please refresh the page and try again.

By submitting your information you agree to the Terms & Conditions and Privacy Policy and are aged 16 or over.

Whether you’re mounting a TV or installing some plug-in wall lights but don’t want to see the wire, or need to hide some cabling that trails across the wall, hiding wires in the wall can make the world of difference to your interiors, keep things looking neat and remove any potential hazards for little ones and pets.

When my friends redecorated following a big water leak, they wanted their new tv on the wall but didn’t want its many wires trailing down the wall to the sockets below and not knowing how to hide them, they dropped me a message to ask for my DIY help.

  • Treat yourself to the best TV too.

Knowing our new-build exterior walls are just plasterboard on top of breeze block and diving walls, with just stud framed and wall insulation behind, I knew it was possible to channel behind the plasterboard and hide the wires in the gap to keep their mounted TV looking seamless and wire free. So I headed round their house with my box of tools and got to work.

(Image credit: Jasmine Gurney)

Whether you have sockets low down on the wall and want to hide wires that would reach up to a wall mounted TV, or would prefer to conceal wires around the baseboards at floor level instead of them traipsing across the wall, this process is super quick and easy and can take less than one hour, depending on your DIY skill level.

  • Find more quick DIY projects to try.

Tools you’ll need to hide wires:

  • Stud/ wire detector
  • Multi-tool with flat saw attachment
  • Drill and screw bits
  • Spirit level
  • String
  • Tape Measure
  • Rawl plugs
  • Brush Wall Plates

How to hide wall mounted TV wires: step-by-step


Safety check and mark up the wall

Grab your stud/ live wire detector and check the area you plan to hide the TV wires behind. Mark on the wall in pencil where your wires go and where your studs are (if any) so you have a clear picture of what’s lurking behind the plasterboard. 

(Image credit: Jasmine Gurney)

2. Check the socket area and cable length

If you have some sockets lower down on the wall that you’d like the wire to come out next to, check around this area so you know where is safe to drill and cut. At this point, it’s also worth checking how long the cables are that you’re planning to hide, to help determine where to put the entry and exit points.

3. Decide where the wire openings should go

Once you have your item or TV mounted on the wall and, your wires and obstructions mapped out, decide where you want the two openings to go. It’s best to have them directly above one another to make feeding the wire through easier.

4. Prepare to install the wall plate

Remove the brush part of the wall plate and using a spirit, mark the internal rectangle/square and screw holes on the wall. I did this right by the TV wall mount so the TV would hide the exit point, and the entry point right beside and in line with the existing wall sockets below.

(Image credit: Jasmine Gurney)

5. Cut the entry and exit holes

Once the entry and exit have been marked, grab your wire detector and triple check there’s nothing behind there. Then you’re free to cut the hole using the flat wood cutting bit on your multi-tool. 

Top tip: If you don’t have a multi-tool, you can drill a hole in all four corners and use a plasterboard knife to cut out the squares.

(Image credit: Jasmine Gurney)

  • Find the best drill for the job.

(Image credit: Jasmine Gurney)

6. Detach the wires from the TV

Detach the wires from your TV and get them ready to feed through. You can either attach the face plates now, or after you feed the wires through the wall. 


Attach the face plates

To attach the face plates, drill a hole where you marked the screw holes with a wood drill bit. Use the appropriate plasterboard rawl plug and screws to attach the plate. Do this for both the entry and exit points, but don’t add the brush fronts just yet.

8. Feed the wires behind the wall

To feed the wires behind the wall, grab a long piece of string, longer than the gap between your entry and exit points and tie a weight (I used a drill bit) to one end, leaving enough string to tie to the wire, or the knot loose enough to undo. 

Drop this weight into the entry point (the top hole) and let gravity take the weight down behind the wall as you feed the string – don’t let go!

Keep feeding down until you see it through the exit point (bottom hole). Grab it and pull through, without letting go of the top of the string.

9. Feed the cable up behind the wall

Tie the bottom end of the string around your cable and start pulling the top end of the string so the cable starts feeding up behind the wall. Once you reach the top, pull enough through needed to plug into the TV and detach the string. Repeat this for any further cables.  

(Image credit: Jasmine Gurney)

10. Finish up

Once you have all your cables fed through, feed the ends of the cables through the brush and clip it onto the face plate. Plug the cables in at both ends, put your TV on the bracket you’ve installed or push your furniture back in place, because you’re done! 

How do you hide unsightly wires?

This simple solution to a wire free wall can completely transform a space and make a TV look seamlessly mounted. This can also work for a wall mounted plug in light if you didn’t want to pay out for an electrician, just use one wall plate at the bottom and cut a smaller entry hole to mount the light on top of, and ensure the wire is long enough to reach a socket below. 

(Image credit: Jasmine Gurney)

If your entry and exit points aren’t quite in line with each other, you can use a metal wire or unbent hanger with a hook on the end or magnet attached to catch the weight and pull it through the bottom hole, of course checking there is no stud in the way that will prevent you accessing the string.

How to hide wires: 7 original ideas :: Design :: RBC Real Estate

Wires and cables can nullify all efforts to create a harmonious interior. If at the stage of repair they were not hidden in the wall or on the ceiling, there are a few simple solutions. To do this, you do not have to spoil the finish.

Photo: Daria Shevtsova/Pexels

It is impossible to imagine a modern house without electrical appliances. Washing machine, computer, refrigerator, TV, router – all this facilitates work and makes our life more comfortable. But the more electronics in the apartment, the more difficult it is to maintain comfort and harmony in the interior. Protruding wires spoil the appearance of rooms, get underfoot, collect dust and complicate cleaning. And most importantly, they pose a great danger to children and pets. Here are some interesting solutions that will help get rid of the clutter of wires and make the interior aesthetic and functional.

Important: any work with electrical wiring requires extra care and strict adherence to safety rules. If you accidentally damage the insulation of the internal wires of the cable, you can not only ruin your favorite household appliances, but also cause serious harm to your health and the health of loved ones.

1. Skirting board with cable channel

This method is excellent for masking long wires. For example, from the antenna. The cable channel can be purchased at any hardware store. It allows you to hide communications from the eyes without chasing the walls and carrying out expensive work, and most importantly, it will fit into almost any interior due to the variety of colors, designs and materials. One of the most popular models is plinth cable channels.


Outwardly, they do not differ from ordinary skirting boards, but they are equipped with special cavities into which the cable is placed. The base is attached to the wall with dowels, glue nails or hidden screws. Then communications are laid inside and the lid snaps into place. Please note that the wire must fit freely in the cavity of the cable channel. Choose a model that will meet this requirement.

2. Spacious organizer

If you have too many wires in one place, just put them in the organizer box. This will create a sense of order, reduce cleaning time and make the space safer. Surge protectors, extra wires, chargers, routers are placed inside the organizer. Today on sale you can find stylish plastic boxes with ventilation holes and silicone legs. If desired, the organizer is easy to make with your own hands.


An ordinary shoe box or an old wooden bread box will do for this. Make the required number of holes for the wires in it and decorate it to your liking. If you don’t want to think about design, choose a ready-made gift box on the Internet. And so that not a single wire is lost, you can stick a small paper label on each and make a signature.

3. Disguise behind furniture

Protruding wires can be masked by using nearby furniture. Glue them to the back of a bookcase, clip them to the back of a countertop, or tuck them neatly behind a desktop leg. To do this, you will need holders to fix the wires. For example, reusable plastic clips with Velcro. If you are afraid to spoil the surface, use ordinary masking tape. In addition, the wire can be hidden behind a curtain, a mirror, a vase, or a plant with dense foliage.


Another practical solution is to purchase a pedestal with a built-in cable management niche, or to create a dedicated wire drawer in the desk. Place an extension cord and chargers from gadgets scattered around the apartment. So you will not only get rid of the tangle of cables, but also make your workplace more organized.

4. Wall installations

Sometimes it is better not to hide the wires, but to leave them in a visible place and turn them into a spectacular decorative element. If the room has a free plain wall, try folding the pattern. These can be geometric shapes, abstract patterns, or realistic images. For example, silhouettes of a city or people. Such installations look especially advantageous in modern interiors.

Photo: Pinterest

Bend the wire in a specific pattern and angle. In this case, it is very important to choose the right fasteners. They should firmly fix the cable on the wall and remain invisible. Before you begin to assemble the composition, draw a wire layout and transfer the sketch to the surface with a simple pencil. This will save time and effort. And if the wire does not fit into the environment, you can repaint it.

5. Vinyl stickers

Wall installations will look more interesting if you add some decorations. Vinyl stickers are perfect for this – even a small cable can be decorated with them. Such products are quickly applied, leave no traces behind and adhere well to any smooth and clean surfaces. Try to make a tree out of wire and decorate it with flowers and leaves – let the plinth be the “soil”. Or draw a separate branch by placing vinyl birds on it.


Now stickers of all colors and sizes are sold on the Internet, so this decor will never get bored. You can always pick up figures for the interior and change them depending on the mood or season. The main thing is to make installations on a plain background. And to make them even more spectacular, use LED garlands, feathers and colored ribbons.

6. Decorative clips

If you don’t have a suitable wall in the room or you don’t want to waste your time on drawing, decorate the wires with decorative clips. According to their design characteristics, they do not differ from conventional clamps and securely fasten the cable in the right place. The difference is only on the outside: these clips look more interesting and are complemented by various elements.

Photo: Pinterest

These can be leaves, figurines in the form of birds or rabbit ears. Remember that the mounting hole of the clip must match the diameter of the cable. To organize wires, instead of holders, you can buy decorative ties or overlays. They will help to beat the nondescript cable stretching along the wall. For example, a camouflage cover in the form of a metal pipe will look great in a loft living room, and a stem overlay is a great solution for a nursery.

7. Colored electrical tape and beads

To turn a wire into an original piece of furniture, it is not necessary to pick it up from the floor. Just decorate communications with any means at hand. For example, wrap with colored electrical tape, textured twine or bright threads. If the cable is thin enough, try stringing massive beads onto it. Designers often use this technique to create ethnic accents. All you need to do is match the color of the materials with the rest of the items in the room. Show your imagination and don’t be afraid to experiment.


Such decorations will not only allow you to harmoniously fit an unpresentable wire into the room’s decor, but also additionally protect it from wear. Thanks to the decorative edging, communications will not be subjected to friction, which means they will serve you much longer.

How to hide the wires in the apartment


The need to mask wires

Why it is necessary to hide electrical wires, why they should not be within reach:

  • this is ugly – the tangles of a bunch of cords in the most prominent places greatly spoil the look of the room, violating the integrity of most interiors, especially “historical” ones. The only exceptions are spaces designed in the style of techno, industrial, loft, art believe;
  • it is not safe – for a cable stretched across the whole room, it is easy to get caught, fall, get injured. Teething children, many pets, are capable of chewing on electrical wires out of curiosity, which often leads to electric shock of varying severity.

In addition to the cords themselves, it is advisable to hide the “boxes” of extension cords, along with a lot of gadget chargers sticking out of them.

Choosing the best wire layout

When deciding how to hide wires, you need to consider their length and structure. When laying along a wall or along the ceiling, the cables must not be stretched. If you do not leave a margin near the TV itself or the outlet, there will be a large load on the plug, and as a result, it or the connector will fail.

Bare wires are also not allowed. It happens that the cable loses its integrity during operation. Areas with cracks or chips in the upper insulating layer must be additionally wrapped with electrical tape or replaced with a new wire.

It is also worth considering:

  • How many wires are planned to be hidden. For one or two, it is easy to punch holes of the required length or purchase cable channels. A large number of cables are best removed into the wall behind drywall boards.
  • Desired Location: Ceiling wiring will require more cable than floor wiring.
  • Distance to outlet. If the TV is located near a power source, you can simply mask or decorate the cable so that it is not conspicuous.
  • Safety indicator. In apartments or houses with small children and pets, special attention should be paid to hiding wires. They should be located in an inaccessible place, for example, in a box or in a wall. But do not just lie on top of the plinth.

Let’s take a closer look at all the options for how to hide the wires from the TV beautifully, neatly and safely.

Disguise options

Wires must be dealt with – all interior designers agree on this. Long gone are the days when wires were allowed to hang freely and lie here and there, like vines in the jungle.

There are two fundamentally different approaches to solving the problem once and for all. The first offers to hide the wires, the second – to beat them in some way.

Hiding wires in the wall

It happens that the wallpaper is already pasted, and you don’t want to break its integrity. There is an option to eliminate protruding cables without serious damage:

  • carefully cut the wallpaper or bend it away from the wall close to the floor;
  • take a handy construction tool, make a neat shallow channel in the wall;
  • lay the wires in the resulting hole;
  • close the channel with a thin layer of plaster, putty;
  • let the mortar dry;
  • stick the wallpaper in place.

If this method is not suitable, you can proceed without chasing – use a decorative cable box. Especially often it is necessary to close the power wires with boxes: they have a large diameter, so they cannot be drowned into the wall without re-repair. It is necessary to buy a cable channel that is suitable in color, width, length, which will serve as an additional element of decor and reliably protect the wiring.

In a wooden house, the box will enhance fire safety measures. This option is also ideal for the bathroom, because it is very difficult to lay wires under the tile. It is only important to remember that all lighting elements, electrical wiring, cable channel must be waterproof.

How else to hide wires on the walls in a beautiful way? If desired, it can be covered with the following trim elements:

  • door frames;
  • various moldings, baguettes;
  • window slopes.

Please note that only low-voltage wires (for example, for the Internet, telephone) can be covered with such materials, and high-voltage cables can only be hidden in accordance with fire safety standards.

Capital measures

If the wall is brick or concrete, cabling is planned in preparation for the repair. Such a prudent approach makes it possible to hide the cables directly into the walls, and the question of how to beautifully hide the wires from the TV on the wall will disappear by itself.

Proven technology is used to tuck cables into the wall. Places are marked on the wall where the strobe (furrow) will break through. The groove is punched with a wall chaser or other suitable tool (perforator or grinder). Cables placed in a corrugation or fastened with brackets are laid in a prepared strobe. When the electrical wires are laid, the grooves are primed and covered with plaster.

Plasterboard walls are easier to wire than concrete. The cable is laid in a corrugated pipe, which has a fire safety certificate. Hidden wiring in the wall is reliable and invisible, and it is impossible to get to it without destroying the wall. Cons – the process is quite costly, dusty and complicated (you will need to draw up a layout according to the rules of SNiP).

Ceiling Wiring

Laying wires from TV and other household appliances under the ceiling is one of the safest ways to hide them from children and animals. Moreover, to create such a system, it is not necessary to ditch and make technological recesses. You can choose one of the following methods:

  • External wiring with fireproof protective sleeves (corrugated). They are matched to the color of the ceiling finish. And they are simply fixed with brackets to the ceiling.
  • Application of ceiling plinths with technological holes for electrical wiring. The fastest and most affordable way. It is enough to fix the skirting boards and run the wires through them to the exit point. Boxes are lowered from it along the wall or wires are removed into the wall.
  • Hidden wiring under suspended ceilings. The design includes a special frame to which wires or wiring boxes can be attached.

It is important to observe safety precautions even when running wires from the TV. Each cable must be insulated. When wiring several wires at once, they are removed into fire-prevention corrugations.

Floor installation

Installation of wiring on the ceiling is convenient if the ceiling is partially or completely made of plasterboard, stretch films, hollow wooden, plastic false beams. Such coatings perfectly mask all cables, corrugated pipes, and other communications. This is convenient in cases where the floor, walls are almost ready, they have a unique, highly artistic coating – it is problematic to change anything.

Cables are allowed along the floor, if this is done on the ceiling, walls is impossible. Then the screed is made four to seven centimeters thick – under such a layer it is easy to hide any number of electrical wires. Another convenience factor is the placement of sockets, switches as close to the floor as possible (30-90 cm). It will take quite a bit to ditch the wall to install the sockets here, the cable savings will also come out significant.

It is important to choose the most durable, heavy corrugation for each cord, and mount most of the wiring at a distance of 20-30 cm from the wall. Fastening to the floor is carried out using flexible perforated tape, textile material or mesh.

Cable channel (plastic box)

Cable channel will help out if you need additional wiring or a socket, and the repair has already been completed. It can be used for wiring on the surface of the floor, wall, ceiling. The plastic junction box is made of non-combustible PVC, protects the cables and restricts access to them, looks as aesthetically pleasing as possible. If necessary, it allows you to organize additional wiring in the future.

Plastic wall mounted TV box is an aesthetic way to hide wiring quickly and easily. The product is suitable for installation only on non-combustible or low-combustible surfaces: plaster, drywall, concrete, brick. The box will be an easy solution if new appliances have appeared in the house and additional wires need to be run.

Cable channel can become a conceptual part of some interior styles. For a room in a classic or eco-style, wood-like models are suitable; the wooden texture is applied to the boxes by thermal printing. For loft and retro styles, plastic pipes that look like brass and copper products are suitable.

Skirting boards with cable channels

Collapsible plastic skirting boards are equipped with holes into which a cord is inserted, several wires at the same time. Advantages of skirting boards with cable channels:

  • no need to ditch the walls, violating their integrity, wasting time on repairing irregularities;
  • the ability to beautifully hide all the wires, almost anywhere in the apartment;
  • the element is flexible enough that it can be used even if the wall is crooked;
  • the plinth is easily washed from various contaminants, does not fade in direct sunlight;
  • available in various colors to match existing flooring.

The cable duct is located inside the structure in the center or in the removable upper half. The first option is suitable when you need to hide three or four wires, the second – for several thick cords. It is important to choose a plinth by color, width, mount it from the inner corners of the room. All corners are closed with special decorative overlays, purchased together with skirting boards.

For timber, concrete, plasterboard walls, appropriate fasteners are used here – the plinth must fit snugly both to the wall and to the floor.

Special cable clips

The easiest way to keep cords out of your way. Staples can be semicircular, rectangular, with a plastic or metal top. They are most often attached to the plinth with a conventional hammer.

This method will not help to hide the wires from the TV, but to ensure free passage through the apartment, corridor, kitchen.

Cable channels, their types for masking wires

Plastic channels, where they put in, stick the cord, are called cable channels. This is one of the most convenient options for hiding electrical wires, used after the completion of finishing work. They are often used in the kitchen – this is convenient when repairs are made, but later additional equipment such as an air conditioner, washing machine, and lighting fixtures are purchased.

Cable ducts vary in color and are easy to replace and supplement with new branches. The design is made of fireproof materials, the cords in it are maximally protected from damage from the outside, ultraviolet radiation. The downside here is that it is problematic to choose colors for some interior styles (baroque, ecological, empire, rustic, etc.), although the design looks much better than wires hanging from everywhere. When the cable channel is located on the corner, any ledge, it is easy to hook it.

The element is made of plastic, metal (galvanized steel, anodized aluminum), it can be U-shaped, W-shaped, triangular, semicircular section. Fastening to the wall, floor, is made with self-tapping screws, dowel-nails, iron brackets, anchors. There are also flexible rubber, wire, transparent options.

Hiding wires in a special box

Unlike decorative boxes, special boxes for extension cords and cables look neat from all sides, so they can be placed next to a computer, TV, on a desktop or on a bedside table.


  • Finding boxes is not a problem. For example, Ikea sells two models – the standard type and in the form of a bag. Also, cable organizers for wires can be purchased at Ozon, as well as in hardware stores.

Camouflage covers

You can make a cover for one or several cords at the same time with your own hands from plastic bags cut into narrow long strips. A kind of “sleeve” is knitted from them with knitting needles or crocheted, into which all the necessary wiring is inserted. To hide the extension cord with charges in this way, a handbag that fits in size is knitted or sewn.

Some shops offer decorative folding covers made of plastic, in the form of tree branches, colored tubes, shiny snakes. This design does not have protective properties, like cable channels, but it is permissible to cover “ugly” wires with it. If desired, a special spiral braid is purchased – it is flexible, has an aesthetic appearance, and allows you to hide both one element and many wires.

Hiding the extension cord in a decorative box

An unsightly extension cord with a bunch of wires can be hidden in a box with holes cut out on the sides and a lid. It’s cheap, simple and practical. There is only one minus – homemade cutouts may not look very neat.

Hint: You can use wicker baskets instead of boxes.

Wire decoration

Design solutions for how to hide wires on the wall beautifully can be very unexpected, complex and simple. Decorators are of the opinion, why hide something, if you can organically fit it into the interior.

The most common decorating options are:

  1. Purchase of special silicone tips. They can be of different colors, shapes, there are even curly options. For example, in the form of a tree with branches in the trunk of which wires are hidden.
  2. Using the curling method. This will require simple brackets-clamps and imagination. The wire can be specially bought in a suitable color, because even HDMI cables are on sale not only in black, but also in red, white, green and other shades. For convenience, you can draw the desired drawing on the wall with a pencil and lay the cable along it. You can get a real picture or elegant curls that match the design and style of the whole apartment.
  3. Hidden behind houseplants. A simple and proven way. The cable is fixed to the wall. Hanging flower stands are made along the wiring. And planted curly or hanging flowers. Artificial options are also suitable for those who do not differ in love for gardening.
  4. Decorative panels. You can buy, order or make your own. Woodworkers can create real three-dimensional paintings, which will provide a secret passage for wires from the TV and other household appliances.

An alternative method for artists is painting on the wall. Under its color, a wire is selected and laid directly on creativity. Some designers equip hidden wiring with LEDs. In this version, the wires from the TV turn into decor at any time of the day.

Tip. Don’t be afraid to fantasize. Even a simple decoration of a wire with artificial flowers may be the most suitable solution for your apartment. But do not forget that any decor will attract the attention of children and animals.

Wire panel

A long wire can become a spectacular wall panel. Give it the desired shape and secure with clips. Cities, animals and even abstract structures can come to life on your walls.

Collecting the cables in the holder under the table

If you collect all the wires under the table, they will not be visible, and the table will be in perfect order.

You can buy this cable holder from Ikea.

Wires as an art object

Creative thought has long been working on making electrical cables minimally noticeable. Many interesting ways have been invented to decorate wires on the wall, including the following options:

Make the wire a decorative detail. If a long wire cannot be hidden, perhaps it will fit into the interior in the form of a wall panel.

It may be possible to build an original composition of wires: disguise the cord as a picture on the wall or use improvised means.

Wire decor on the wall can be emphatically decorative. Some manufacturers offer unusual collapsible plastic construction. They do not have a protective function, but somewhat streamline the space.

We cover the cables with a plastic box

This solution is especially relevant for masking wires near the TV.

Hint: Ideally, the box should be painted to match the wall.

Cable as an interior detail, style

Loft is one of the few interior styles in which it is permissible not to hide, but on the contrary, in every possible way emphasize the presence of wires in various places. The original retro-style wiring, which not so long ago was found only in really old houses, is now offered by many companies specializing in electrical wiring.

In such an interior it is easy to meet:

  • twisted electrical wires “ivory”, “copper”, “brass”;
  • domed retro switches in ivory look;
  • Antique sockets;
  • Aged silver look cords.

Wires are not hidden at all in the loft, but no one canceled the safety here – when there is a risk of accidental damage, it is better to hide the element in massive cable channels stylized as copper, steel, corrugated pipes, wooden boxes, etc.

Fixing wires with clips

To organize the chaos of wires lying on the floor or table, fix them on the wall or furniture body with special clips.

You can fix the wires with a furniture stapler.


  • Cable clamps are available at hardware and hardware stores;
  • In order not to get confused, all wires should be marked with self-made labels as in the photo below.
  • It is better to use discreet transparent clips, for example, from Command, as in the photo below.

Ideas on how to hide the cable from the TV, home theater

The owner of an apartment or house wants to have as few wires as possible, more precisely, so that they are not visible. To quickly hide cables, you can buy special furniture, which already has technological holes for antenna or cable wire.

Most often, such furniture includes TV cabinets. They are equipped with a hole where you can easily and quickly remove all the wires. And discreetly connect them to the nearest outlet. In the same cabinets there can be retractable shelves for TV set-top boxes, DVD players and other equipment.

Position the TV stand as close to the outlet as possible. If this is not possible, you can run an extension cord under the plinth and bring the power source as close and imperceptible as possible.

Tips, ways to hide wires in the workplace

In the home office, to make it look neat, the laces coming from the computer, the router also need to be removed. A clerical clip will allow you to “put in” a cord that gets tangled under your feet, under the surface of the table – from its very edge. The clip is easy to fix on a wall, a shelf, and several of these parts make a kind of separators for the inputs of different charges.

If possible, wires hanging from the back of the table are simply covered with a textile curtain. Some of them can be arranged in a mini-hammock – the “head” of the extension cord can easily be placed there along with chargers that interfere strongly on the table.

Separate companies produce special wire separators – two or more cords are neatly placed inside a wooden, plastic, rubber or metal structure. A cool store option for holding wires, looks like two wire electric towers. Pockets made of plastic bottles, clothes pockets look funny – the product is hung on a wall socket, charging is turned on, and the phone itself and the cord from it lie quietly in the pocket.

With a simple upgrade of the table, which has spacious drawers, all the electrics are neatly hidden there.

Fasteners on the reverse side of the countertop tables or TV cabinets

As you can see from the range of devices offered, there are two ways to attach wires from the computer to the reverse side of the countertop:

  • With double-sided tape. Not always reliable, but modelable.
  • Self-tapping. The main thing is to use the “correct” self-tapping screws, no longer than the thickness of the countertop. As a rule, 3.5×16.

It is not always acceptable to make holes in the tabletop itself or the table stiffener. And it is inconvenient if the workplace is already assembled and stands in its place. Therefore, a perforated screen is often used as the basis for attaching cables and power supplies.

Or a metal mesh shelf of suitable width and depth. This option is more expensive, but much stronger and more durable.

Using the same harnesses and clamps, wires with all accessories are attached to the base. And only then, after the final “assembly” – to the reverse side of the countertop or stiffener. So much more convenient.

How to hide wires from charging

A modern person often has to charge several devices at the same time. When all of them are inserted into one “tee” or “multi-tail” charging is used, with three to five cords for different devices, all elements are assembled under one stationery clip, attached to any nearby surface. Some purchased options are separator boxes with four to six shaped holes through which only the “tails” of the charges are output.

This item is easy to make with your own hands, by upgrading a simple shoe box, covered with fabric, wrapped in colored paper.

Original and simple methods to hide TV wires

Imaginative designers and homeowners come up with unusual ways to hide TV wires and decorate an apartment or house at the same time. The simplest and most original options include:

  1. Put on the nightstand and cover them with books or special decor elements. The main thing is not to forget that books are for beauty, and not for reading.
  2. Braid the wires with a thick rope, turning them into a real decoration of the apartment, from which you can create a tree on the wall or any other pattern.
  3. Phytowall placement is a modern solution for stylish apartments. This is a special panel with pockets for indoor plants. It is enough to place the TV with your back to a living wall and run the cable behind it to neatly and beautifully hide all the wires. At the same time, this design of the TV zone will help you completely relax while watching TV.
  4. Installation of decorative furniture. If the TV is fixed on the wall, the wires go down and spoil the design. To hide them, it is enough to create a thin TV cabinet. It will look stylish and at the same time close the wiring and outlet for the TV.

There are a lot of options for hiding wires from household appliances on the wall, ceiling in the floor. Choose any that suits the design of the room, and do not be afraid to create. But do not forget about safety precautions.

Hide wires in a recess, drawer or shelf

At the project development stage, special niches and sections can be provided where power supplies will be attached to the required number of sockets. You can also leave a place there where you can “pull in” neatly folded wires so that they do not hang around the wall and floor. Indeed, at the measurement stage, it is already clear both the location of the table (or TV cabinets) and the position of the sockets.

An interesting solution is to allocate a drawer or drawer (a shelf for a keyboard in the standard sense) to organize the connection system.

In this case, the pull-out mechanism should be supplemented with some kind of folding cable channel for wires, which will not sag and “interfere” with the movement of the drawer or shelf.

If the TV is hanging on the wall, then the dangling wires to the cabinet can be covered with false panels and shelves. From their inner side, the depth is “selected” in order to mount a compact cable channel. It is recommended to separate low-voltage and power wires (when it comes to connecting audio and video equipment) and hide them in different cable channels.

Cunning disguise

The wire from the table lamp is trying to get under your feet! Fortunately, it is easy to hide behind the table leg by attaching it with clips.

Safety – how to hide the wires from the child

Many companies producing household goods produce a whole series of protective elements designed to protect the little man from electric shock as much as possible. Companies such as Ikea produce convenient wire holders – they are difficult to gnaw through, break, and two or four cords can easily fit inside.

Special integrated designs that allow you to charge your phone or tablet are built into any furniture surface – they are easy to place out of the reach of a child. The same company produces boxes, bags-cases with buttons – they hide extension boxes, partly electrical wires, which allows you to give a neat appearance to the whole room. For individual devices, there are completely wireless designs – to charge a tablet, phone, player on them, you just need to put the gadget on such a charger.

If it was not possible to purchase protective items for laces, extension cords, all “dangerous” items are hidden in large cardboard, plastic, wooden boxes, which are placed in places inaccessible to the baby.

Useful tips

In order not to get confused when masking wires and not to get into trouble during repairs, they must be marked in advance. This will help you immediately find the right cable later. It is better to separate low-power wiring from power wiring, without connecting it into a single bundle. Wires from the antenna, the Internet should be placed separately from others, so as not to spoil the signal quality.

Cables should be as short as possible and have as few connections as possible: this increases their safety and reduces the risk of injury. It happens that the braid of hidden cables is frayed at an unsuccessful location, so wiring in dangerous places should be checked more often. If you need to mask the wiring, you can apply any ideas, especially since the range of tools and materials for decorating is now huge.


Wireless technology is still not widespread – the vast majority of electrical appliances have to be plugged into a power outlet. The way out is to hide the cords in the cable channel, in the wall or under the baseboard. It is also possible to make a real work of art out of a long wire using original decorative elements.