Cold water tap in kitchen not working: 9 Reasons No Cold Water Is Coming out of Your Faucet

9 Reasons No Cold Water Is Coming out of Your Faucet

Photo: Yevhenii Podshyvalov / iStock / Getty Images

If your faucet’s running hot, these tips will chill it out

Get quotes from up to 3 pros!

Enter a zip below and get matched to top-rated pros near you.

When you aren’t getting any hot water, you know the likely culprit is the water heater, but what do you do when the problem is a lack of cold water? There are only a certain number of issues that could lead to this problem. Follow these steps to figure out if it’s a minor repair you can correct on your own or if you need to call in the plumber.

1. Check the Water Main or Water Supply

Uh oh. There’s a heatwave and you’ve just spent an hour gardening. You’re looking forward to that glass of water to cool down but suddenly realize there’s no cold water coming out of the faucet.

Before getting too far into diagnosing the problem with the tap in question, you should rule out a more widespread issue. Is hot water coming out of the tap? Are the other faucets working? What about the shower? If the answer to any of these questions is yes, you can be confident that it’s not a general water failure caused by the water heater or a problem with the water main or your water supply.

If you’re not getting water anywhere in the house, find the water main valve—typically in the basement, under the sink, or near the water heater—and confirm that it’s open. If that doesn’t solve the issue, check with your neighbors to figure out if they’re having similar issues before contacting your water supplier.

2. Check the Shutoff Valve

The pipes to each sink in your house are outfitted with a shutoff valve that allows you to stop the water supply locally without affecting the rest of the house. If you have kids or pets, it’s possible that they inadvertently closed the valve—or, if you’ve had repair work done recently, it could be that the plumber neglected to open it back up after the job was complete.

Under your sink, trace the pipes that supply it with water and search for a knob or lever. Turn it counterclockwise as far as it will go to confirm it’s fully open.

3. See If the Supply Line Is Kinked

Photo: Jose Luis Pelaez Inc / DigitalVision / Getty Images

While you’re looking under the sink, another potential issue to check is if the supply line (the thinner line of piping connected to the sink) has become bent or kinked. Though most newer homes feature braided steel lines that are difficult to damage, many older builds still include a more flexible copper or all-metal version that bends easily, choking the water supply.

If yours appears to be out of shape, try manually straightening it and see if that gets the cold water running again.

4. Try the Spray Nozzle

If your faucet includes a separate spray nozzle, it’s possible that the feature’s stutter valve, which diverts the water to the nozzle when it’s in the open position, has become stuck. Try running the water through the spray valve a couple times, and see what happens.

If you’re getting water there but not out of the faucet, it’s safe to assume the stutter valve is to blame. Turn off the flow of water to the sink using the shutoff valve, which is attached to the pipe underneath. Next, turn both the faucet and the spray nozzle on at the same time before opening the valve again—this should disengage the nozzle’s vapor lock and return water flow to the faucet.

5. Look for a Frozen Pipe

If you live in a cold climate, and you have not winterized your pipes, the most likely culprit in your cold water problem is a frozen pipe. If the sink’s pipe is located behind cabinet doors, open them up to let in a little heat from the house.

If you regularly experience cold periods, it’s a good idea to get in the habit of leaving the cabinet open to prevent the pipe from freezing again in the future. For a little extra power, you might also use a portable heater if there’s a safe spot to put it nearby or a hairdryer. If it was frozen solid, the ice may have damaged the pipe or the faucet, so there’s a risk that thawing the pipe could lead to a leak. If this happens, it’s time to call a plumber.

6. Search for Leaks

If a pipe is leaking somewhere in your house, it could be cutting off the flow of water to the tap in question. Trace the pipes throughout your house and see if you can find evidence of a leak somewhere. There are some short-term solutions for leaking pipes that might lessen the damage, but you’re going to need to call in a plumber to get the cold water flowing again.

7. Investigate the Water Purifier

Some kinds of under-sink water filter systems can trigger an automatic shutoff to your faucet if the pressure becomes too high. If this is the reason no cold water is coming out of the faucet, you can manually set the water to bypass the unit, restoring the flow to the tap—just remember that until you correct the issue with the unit, this water will no longer be filtered.

8. Replace the Washer

Photo: Jose Luis Pelaez Inc / DigitalVision / Getty Images

In some cases, a tap can become blocked simply because the washer has loosened and dislodged, physically blocking the water flow. Turn the shutoff valve, disassemble the faucet, and replace the washer with a new one. If you get a smooth flow of water, your problem is solved!

9. Check Your Faucet Cartridge Hasn’t Gone Bad

When your shower tap isn’t producing cold water, it’s likely a problem with the pressure-balancing valve in the shower faucet cartridge. You’ll have to turn the shutoff valve, remove the faucet handle, and take out the old cartridge—located behind the escutcheon (the metal piece used to hide the hole in your wall where the pipe comes through) and often held in place by retaining clips.

Many can be removed with a pair of pliers, but if yours requires a cartridge-pulling wrench, it may be easier to call the plumber than to do it yourself.

Know When to Bring in the Pros

Once you’ve tried all the relevant options above, it’s safe to assume that the problem is too complex for a DIY fix. The most likely cause of no cold water coming out of your faucet—especially if the blockage was preceded by a steady decrease in water pressure—is a build-up of lime scale, created by mineral deposits from hard water.

The long-term solution will require installing a different kind of pipe, or adding a water softening system, but you’ll want to leave the determination to a trained plumber.

Need professional help with your project?

Get quotes from top-rated pros.

Reasons Why Your Cold Water Faucet Aren’t Working – Forbes Home

Owning a home can be a wonderful experience: you get to paint the walls whatever color you want and you can have a pet without having to ask for permission. But then there’s the less fun stuff, too, like having to troubleshoot common plumbing problems, like a lack of cold water coming out of your faucet.

There are many reasons that you might not have cool water at the tap, but several are easy to address yourself or are inexpensive for a plumber to repair. Here’s a quick list of the most common reasons why no cold water is coming from the faucet, depending on where you live.

THIS IS AN ADVERTISEMENT AND NOT EDITORIAL CONTENT. Please note that we do receive compensation for any products you buy or sign up to via this advertisement, and that compensation impacts the ranking and placement of any offers listed herein. We do not present information about every offer available. The information and savings numbers depicted above are for demonstration purposes only, and your results may vary.

Looking For Experts To Solve Your Plumbing Problems?

Finding a reliable Plumber in your state doesn’t have to be a hassle. Choose from a list of top-rated plumbers with extensive knowledge and experience on Angi.

Find A Plumber

5 Reasons Why There’s No Cold Water Coming From Your Faucet

1. Cold Water Lines Exposed to Warm Environments

It’s not uncommon for homes to have plumbing running through uninsulated spaces, like attics. As your attic warms up, the cold water sitting in the pipes, just waiting for you to open a faucet, gets warm, too. Depending on just how hot the attic gets, your tap water may seem alarmingly warm coming out of the faucet, especially in the hottest summer months.

If you notice that your tap water is warm in the summer, but cooler in other times of the year, attic plumbing may be to blame. Open the faucet and let it run until the water cools for an immediate solution. In the longer term, it’s going to be important to address the heat in your attic and insulate the plumbing running through it. By cooling your attic off, you’ll cool off the water and also make it easier to cool your home in the hottest time of the year.

2. Frozen Cold Water Supply Lines

The opposite problem of plumbing in the attic that’s way too hot, is plumbing that’s freezing up because it’s in a very cold space, like a crawl space or an attic in the wintertime. When the weather gets too cold, it’s easy for already water lines to go ahead and freeze completely. If you’re getting little or no cold water and it’s cold outside, this is a likely culprit.

Frozen pipes are a challenge. You don’t really know how much damage has taken place until after the thaw, and then you may suddenly have a flood on your hands. Fortunately, many frozen pipes will thaw without any severe consequences. If freezing is a problem, try wrapping your plumbing with heating tape or installing pipe insulation to help protect from the cold. In addition, closing crawl space or attic vents can help keep the temperature above freezing.

3. Closed Shut-Off Valves

Although it might seem like a silly thing to ask if the shut-offs are turned off, it’s a really easy mistake to make, especially if you’ve been recently dealing with plumbing issues. Sometimes, older shut-off valves can be a little sticky and hard to turn on or off due to years of simply sitting and doing nothing. If your cold water shut-off valve is stuck in the closed position, you’d only have hot water coming out of the tap.

First, check that little to no water is coming out of the faucet when you turn on just the cold water. If it’s a trickle—or less—get under the sink and look for the shut-off valve. Open the valve slowly, by turning the valve counterclockwise. If that valve is open, check the main shut-off inside your home. This is usually a wheel or lever. Turn it counterclockwise slowly to open it up and release the water into your pipes.

Explore A Large Selection Of Stylish Kitchen Faucets Online

4. Lime Build-Up Plugging Your Faucet

Lime is what happens when the tap water evaporates and leaves behind mineral deposit, so it makes sense that faucets can be plagued by this when you have particularly hard water. If your faucet has a crusty glaze where the water comes out, your lack of cold water could be due to a mineral plug in either the end of the faucet or the aerator. If you have a sprayer, you can test this by turning the cold water on and using the sprayer to see if cold water comes out.

If the sprayer is working properly, you can eliminate lime build-up by simply removing the aerator and submerging it in a lime-removing cleaner for a few seconds, or using the same cleaner on the part of your faucet where water comes out. Some people swear by placing a bag of vinegar over the end of a faucet and securing it, but this could discolor your faucet, so test on a small, hidden area first.

5. Failure Within the Faucet

Even the best faucets will eventually have a part that gives up the ghost. When cold water is lacking to just one faucet, it’s possible the problem is the faucet itself. If you’ve gone through the simple stuff and have not gotten the cold water flowing, it may be an issue with the faucet’s cartridge or one of the parts within the handle stem assembly that allows water to flow freely.

Repairing either of these items is a more advanced DIY project, so may justify a call to a plumber. Faucet repair kits are available if you’re feeling particularly handy, but you’ll need to have the specifics of your faucet, including the manufacturer and number of handles, to choose the right one. In some cases, it’s simply easier and faster to replace the faucet itself.

Compare Quotes From Top-rated Water Heater Installers

Free, No-commitment Estimates

Find a Water Heater Installer

Less Common Causes of No Cold Water From the Faucet

If your home has always had issues with a lack of cold water coming from the faucet, your problem could be a much larger one. Sometimes, DIY plumbers make some poor choices about plumbing placement, and may run cold and hot water lines too close together, effectively heating the cold water line using the hot water line. If you can access your plumbing, it would be worth taking a look at the placement of the lines.

Other unusual reasons for no cold water can involve issues with your hot water heater or water softener, damaged copper tubing and other problems that should be addressed by a professional plumber.

Your Home. Your Decisions. Our Support.

Get expert advice on your home, design tips, how much to pay for pros and hiring experts, delivered to you daily.

Thanks & Welcome to the Forbes Home Improvement Community!

I agree to receive the Forbes Home newsletter via e-mail. Please see our Privacy Policy for more information and details on how to opt out.

How to open the water supply tap if it does not open: the reasons for this situation

Content

How it works

Operating tips

Ball valve does not turn, what to do

How to replace a water shut-off valve

Causes of breakdowns and remedies

Repair tools

faucet installation

How to disassemble the single-lever ball mixer

Problems under the sink or above

Principle of operation

The valve is an all-welded or integral body. The first in the event of a breakdown cannot be repaired, and a new one has to be installed. The maintainability of the second is rather conditional, since not everyone can assemble it.

The faucet body is made of brass, silumin, carbon steel or stainless steel. The conditions of use depend on the material. The locking balls are made of the same material as the body. These elements are always round and have a smooth surface.

The ball has a hole inside which, when aligned with the pipeline, allows the fluid to flow. If you put the faucet handle at a right angle, the flow of water will stop. Placement in an intermediate position allows you to adjust the flow of water.

Control the ball through the stem handle that fits into a slot on the stem. If you do not use the tap for a long time, then the minerals that make up the water settle on its surface, and the handle cannot be turned. In such conditions, it is dangerous to use the structure, it is necessary to carry out repair work.

Operating tips

To avoid souring the ball, it is necessary to carry out prophylaxis once a month. It is enough to close and open it.

Preventive measures to avoid problems with the equipment

This will get rid of salt build-up and extend the life of the product. You can scroll the tap while taking meter readings.

Attention! It is impossible to turn the handle sharply, the procedure should be carried out smoothly, otherwise water hammer can be caused. This rule is especially important to observe for people living in apartments of multi-storey buildings, since water is supplied under high pressure, as well as for those who have old metal pipes installed.

It is important to follow these guidelines:

The tap that shuts off the water does not turn what to do – depends on the situation. If it soured at the entrance to the apartment, it is necessary to block the riser. Only then you need to start repair work. Otherwise, you can accidentally flood the neighbors.
It is better to handle the crane in the morning. Thanks to this, if an accident occurs, it will be easier to get through to the appropriate services.
When choosing a crane, pay attention to weight and appearance. The most reliable are heavy models with thick walls.
Brass is more efficient. You can determine this material by the type of crane from the inside. If this body part is yellow, it is brass. Such products are heavier than from silumin.

Products with a butterfly handle are more difficult to turn, so it is better to use options with a regular handle

Important! Such a valve is indispensable, since it allows you to regulate the flow of fluid through the pipes.

Ball valve does not turn, what to do

If the tap that shuts off the water does not turn, it may have soured. This happens if you do not twist it for several years. There is a way to get rid of salt deposits, but after using it, scratches can form on the inside surfaces of the faucet, reducing its ability to withstand fluid pressure.

Do not use pliers or be rough. First, to get rid of the malfunction, it is necessary to unscrew the nut from the stem and remove the faucet handle. There will be a nut underneath. It should be unscrewed with a key, but not completely, but slightly loosened. This element is present on all cranes, so it cannot be confused.

If the faucet is soured, it will be quite difficult to turn it by hand.

The stem of the product has two flat parallel surfaces. You need to take a wrench for them and scroll in different directions. It is important to do everything slowly to avoid breakdowns.

After the stem seal is loosened, leakage will occur from under it. To avoid this, it is enough to tighten the nut at the end of the manipulation.

If the clamp nut is missing and leaks occur, a new valve will have to be installed.

How to replace a faucet that shuts off water

If the main valve is turned off, all the necessary parts have been purchased, you can proceed with the installation of a new product. It is necessary to screw the new element to the pipe using a wrench, check the correctness and reliability of the installation.

Once the tap is in place, the water can be reconnected. It is important that the fittings fit snugly. To do this, tighten them with a wrench and turn on the main tap. It is also worth determining if there are leaks. The replacement procedure is quite simple, even a beginner can handle it.

Replacement process

Causes of breakdowns and solutions

Various problems can arise with ball valves. To fix a problem, you must first know its cause.

leak

If the seals are not tight, the valve starts to leak. This also happens when small contaminants get into the rotary mechanism. This accelerates the wear of the sealing gum or does not allow it to fit snugly.

Also, damage can be on the ball itself if mechanical impurities have got in or it is of poor quality.

If the tightness is broken, you need to tighten the connection with the crown, so that it fits more tightly to the ball.

In the case of blockages, the internal parts must be dismantled and cleaned. It will also be useful to install a strainer on the pipes so that small grains of sand or pieces of rust do not enter the faucet.

A damaged ball must be replaced. The same should be done with seals whose service life has expired.

Leaks are difficult to fix: if the equipment is cracked, it will have to be replaced

Crack in the faucet body

It will not be possible to repair the structure, the entire body will have to be replaced. You can fix the leak for a while by cold welding. Before that, clean and degrease the damage with acetone.

The valve is difficult to close or does not turn

How to open the water tap if it does not open can only be determined after examining the rotary mechanism of the shutter. Difficulties arise when it breaks or becomes clogged. To solve the problem, you should disassemble the structure, remove the handle and unscrew all the details. After that, you need to place new ones.

If the seals and washers are worn out, repair will not help, parts will need to be replaced.

Also unable to scroll if the device is rusty. You can correct the situation with hot water, a torch, a solvent. You can also lightly tap with a hammer.

Water runs poorly when the device is turned on

If the pressure is low, it is not necessary to immediately start dismantling the valve. You must first turn on the water in the remaining devices. You can also ask your neighbors, perhaps the pressure has decreased with them. Then you should contact the utility.

The cleaning screen can be checked. Debris can accumulate on it, which forms a blockage.

The problem is not always related to the deterioration of the faucet, sometimes the pressure drops in the entire water supply network

Tools for repair

Most of the flats are equipped with flange constructions. They are reliable and suitable for pipes of any size. To fix the crane, you need to acquire:

pliers;
wrench;
hammer and screwdriver;
Allen key;
spare parts;
scraps of cloth to remove dirt;
rust removers;
silicone grease.

Shutting off water when the tap is jammed

For safety, it is worth placing valves at the entrance to the dwelling, with which you can turn off the water if necessary. Ball valves, the size of which is determined in inches, cope with this task. If this device is very old, it must be replaced, because such a tap does not shut off the water, and when it flows, it cannot be stopped.

In case of failure of the crane, it is necessary to check all elements

How to Disassemble Single Lever Ball Mixer

Problems may be related to the design of the valve train. To do this, the device must first be disassembled. For this:

Remove the lining and unscrew the lever.
Unscrew the dome cap. It may have pins to make it easier to grab the part. But in their absence, it is necessary to use a screwdriver, installing it in the groove, and, turning it clockwise, rip off the part. You can also carry out the procedure with the help of round-nose pliers.
When the cap is removed, remove the cam and clean all parts from dirt.
Remove valve seats. To do this, use a thin screwdriver or tweezers. With their help, it is easier to get the springs under the saddle.

Main problems with ball mixer

The device may experience the following faults:

The inside of the washer and seat are worn out or dirt has accumulated there. These cavities need to be cleaned.
The ball wears out. Under the influence of too hard water or solid particles contained in it, furrows appear on it. The only way to fix this is to replace the element.

Ball mixers are simpler and more durable than other models

Valve seat has expired. If these parts do not fit snugly against the ball, then fluid will pass through. In this situation, replacement is also required.
Weak springs. At the same time, saddles do not fit well. You will need to install new items.

After cleaning and lubricating the parts or replacing them with new ones, it is necessary to assemble the mixer.

Swivel spout not working

Why the faucet does not turn off the water is not easy to find out, because there can be many problems. If fluid is leaking below or above the spout block, the seals may be worn out. These elements are a rubber ring. Sometimes cuffs are purchased for these purposes.

To replace the mixer you need:

Remove the cartridge and remove the turntable. There are models in which you need to pull up to disassemble, but in most cases it is removed down at the junction with the corrugated hose. To remove the block, it is necessary to disassemble the entire mixer and even the sink.
Unscrew the nut from the bottom of the mixer and pull out the ring.

Swivel spout block

Then remove the spout block by pulling it down. At the junction of the structure with the body, you can see the seals that need to be replaced. It is necessary to buy the same parts, as well as replace the fluoroplastic rings. Then install the device.

If the body is cracked, you can repair the damage with sealant, but this will not last long and you will have to buy a new faucet.

Clogged aerator

If you open the faucet all the way and the water is not flowing with enough pressure, there may be debris in the pipes and inlet hoses or a problem in the water supply. But sometimes pollution can accumulate on the aerator. To remedy the situation, it is necessary to unscrew the element manually or with an adjustable wrench.

After this, deposits or solid particles can be seen on the screen, due to which the liquid cannot flow. To remedy the situation, you need to rinse the mesh under the stream.

Problems under the sink or above

If you are concerned about dampness and accumulation of liquid under the sink, you need to evaluate the condition of the siphon and corrugated hose. If there are no malfunctions, then you need to assess the condition of the crane itself.

The main problem that owners of ball mixers face is the rapid wear of rubber or Teflon seats. After all, it is on them that the ball lies. When their service life ends, water begins to seep. To prevent such problems, you should replace the products every few years.

The deterioration of disc mixers is due to hardness and clogging of the water. Over time, cracks form on the ceramic surface, which also impair mixing accuracy and contribute to the formation of leaks. To solve the problem, you need to replace the cartridge.

Dampness under the sink is a common problem that occurs under the influence of various factors. This is the main disadvantage of cheap products that have a small tuning angle. Therefore, it is better to use models from a trusted manufacturer. A setting angle of 15 degrees is preferable.

Other Possible Causes of Faults

In addition to breakdowns in which the cold water tap does not open, the following problems may occur:

Water leaking through the faucet due to an incorrectly installed lever. If this is the main reason, you need to sort out and adjust the lever during installation.
Damage to the mixing ball or housing. At the same time, a puddle will always be present near the tap. It also occurs when the quality of the seals is poor.
Faucet problems causing contamination of the mixing chamber.

If the cold water faucet does not open, it must be thoroughly inspected

How to fix a cartridge faucet

To fix the damage, you need to install a new cartridge, which is included in the faucet design. For this you should:

Use a soft cloth to wipe the housing, remove limescale residue and check for damage.
Insert cartridge. Installation is facilitated by the presence of centering lugs. They must be connected to the threads on the body.
Tighten the nut without applying excessive force. Otherwise, you can bend the cartridge, which will lead to new leaks. Therefore, it is worth slightly tightening and turning on the water. If it appears from the sides of the case, then you need to turn it off and tighten it a little more. Repeat the procedure until the faucet is dry.
Next, place the cap, put the lever and tighten it with a screw. You also need to place plugs with liquid temperature indicators.

Gasket replacement

If the leak is due to a gasket failure, it should be replaced. If this is not done, then even when the valve or faucet is closed, water will flow. The situation worsens when the user applies excessive force to close or open the faucet. Such features of the operation of the mixer are due to the fact that in Soviet times, the taps were equipped with poorly milled seats, and the valve had to be turned hard to tighten it.

To replace the gasket, the water must first be turned off. After that, you can remove the old one and mount the new one. If there is no gasket at hand, and you need to replace it urgently, you can make it from a piece of leather or rubber by cutting the part along the base, but with a large diameter.

It must be remembered that rubber elements do not fit tightly enough, and leather gaskets are used if the saddle edge is violated. The thickness of the new part must be at least 3.5 mm. If the faucet is too noisy, cut the edges of the gasket at a 45 degree angle.

A quality gasket will ensure the tightness of structural elements

For cold water, a gasket made of sheet rubber or a regular shoe heel is suitable. Flexible plastics and porous rubbers are not suitable. But for hot water, this option is not suitable, as the part will quickly collapse. Therefore, for this it is worth making a gasket from a car tire, it is stronger.

Crane installation

What to do if the tap for some reason does not turn off the water, many apartment owners ask themselves. Some breakdowns require a complete replacement of the plumbing product. The need for this arises when leaks from under the stem. This phenomenon is associated with the gland packing loosely adjacent to the surface. It needs to be replaced.

Maximum tightness is achieved by twisting the stuffing box. It is not advisable to use pliers or sharp pliers, as the borders of the sleeve will be damaged. You can fix the part with a wrench or adjustable wrench. When tightening the sleeve, do not press too hard, otherwise the thread will deteriorate and you will have to install a new device.

Single lever mixers for kitchens and bathrooms

Tightening the sleeve is important to avoid future leaks. If the situation does not change, you should turn off the water and replace the tap or bushing by adding stuffing box packing.

When starting repair work to replace a faucet, the water must be completely shut off or the neighbors may be flooded. After that, you need to pull out the sleeve and unscrew the union nut. To do this, use a sharp knife or a small screwdriver. After that, the stuffing box is taken out and new stuffing material is put in.

To combat leakage, it is also necessary to seal the gland by wrapping the base with burlap, linen or other material.

After locking the union nut, water will not drip. It will not help to solve this problem for a long time, but this is a pretty good temporary measure.

After checking and replacing all failed elements, it is necessary to assemble the crane in the reverse order

Installing a faucet if the water does not shut off

You need to act quickly by unscrewing the broken version with an adjustable wrench. After that, you need to insert, overcoming the pressure of the liquid, the sealing element to a certain depth. Only three steps: unscrew the tap, water gushed, insert the device.

Ball valve breakdown prevention

If the plumbing has to be repaired frequently, then the water in the house is of poor quality. Installing a filter will help fix the situation. A conventional element that is attached to a corrugated hose allows you to increase the life of the devices. Thanks to this, the silicone elements will not wear off.

A special feature of a mixer with a lever is that it regulates both pressure and temperature, and in a simple mixer tap-boxes are responsible for this. Turning the knob allows you to set the desired temperature and pressure. But in single-lever devices, you can change the pressure while maintaining the desired temperature, since the change in pressure occurs when the lever is moved up or down, and to control the temperature it is turned to the right or left.

Brass body models should be used to reduce ball valve failures

The long service life of such devices is due to the fact that there are no rubbing parts and rubber seals in the composition. Ceramic parts can be used, but they deteriorate faster if they are exposed to mechanical impurities present in the water. Only a water filter will help to avoid this.

When the ceramic discs are worn, the faucet will not close or leak water. To fix the problem, you need to get rid of the plastic plug. She is poked with a sharp object. Under it is a groove with a locking screw. Having unscrewed it, you need to remove the lever. Locking screws are usually made for flathead screwdrivers. Less often, cross or hexagonal ones are suitable for them.

After removing the mixer arm, unscrew the nuts that hold the cartridge firmly against the mixer seat. You can remove them with an adjustable wrench or an ordinary gas wrench. The failed cartridge must be removed and a new product installed. It must be installed in such a way that its holes fall into the protrusions located on the bottom.

After repair work it is necessary to connect the water and check the mixer. If everything is done correctly, then there will be no leaks.

Such taps are installed for safety, as they allow you to turn off the water at any time

Briefly about the main

The faucet that shuts off the water has broken, what to do can be found out after inspecting the device. There may be several reasons for the breakdown, so you need to unwind the crane and inspect all the details. If some of them are worn out, you will have to put new ones. A number of breakdowns lead to the fact that it is necessary to completely replace the equipment. Therefore, filters should be installed if the water is hard or with mechanical impurities, periodically turn the valve so that it does not turn sour and perform other preventive procedures.

Have you ever been in a situation where you needed to repair or replace a tap? Were you able to determine the cause of the problem? What would you advise others to pay attention to when operating such a crane?

Service center

IP Marov Stepan Valeryevich

Minsk, Belarus, Yana Chechota street 28

OOO SKL

St. Petersburg, Pulkovskoe sh., 56

IP Gostevsky O leg Mikhailovich

Abakan, Rep. Khakassia, Itygina st., 15A

IP Krylov Viktor Viktorovich

Almaty, Kazakhstan, Brodskogo street 37A

IP Shirokiy Dmitry

Novorossiysk, Krasnodar Territory, Dzerzhinsky Ave. , 211

IP Klimovich Yury Evgenyevich

Armavir, Krasnodar Territory, st. Engelsa, 101

IP Gavrilova Natalia Ivanovna

Krasnodar, Krasnodar Territory, st. Dzerzhinsky, 119/2

LLC “APOLLO-plus”

Barnaul, Altai Territory, Partizanskaya st., 44

IP Chumak Dmitry Viktorovich

Dubove, Belgorodskaya obl., Yagodnaya st. Sovetskaya, 14

IP Kudryavtsev Sergey Mikhailovich

Moscow, Bashilovskaya st., 15

IP Kudryavtsev Sergey Mikhailovich

Murmansk, Murmansk region, Karla Marksa, 29

IP Lipkov Alexey Alexandrovich

Veliky Novgorod, Novgorod region, st. Fedorovskiy ruch., 2/13

IP Marov Stepan Valerievich

Saratov, Saratov region, st. Osipova, 1

IP Irbakhtin Andrey Nikolaevich

Samara, Samara region, st. Karbysheva, 65B

IP Shelyagin Leonid Vladimirovich

Yekaterinburg, Sverdlovsk region, Vostochnaya st., 44 Chapaeva, 7

IP Britanova Lyubov Alekseevna

Nizhny Tagil, Sverdlovsk region, st. Parkhomenko, 30

ASC “Motive”

Chelyabinsk, Chelyabinsk region, st. Shumenskaya, 31A

IP Barabanov Sergey Viktorovich

Rostov-on-Don, Rostov region, Elevatorny per., 7 Konechnaya, 5

Sibkomplektservis

Tyumen, Tyumen region, st. Energetikov, 55A

IP Kharisova Liliya Gaifievna

Kazan, Rep. Tatarstan, st. Maksimova, 50

LLC “Leader”

Naberezhnye Chelny, Rep. Tatarstan, Mashinostroitelnaya st., 36

Strokach Oleg Vladimirovich

Khabarovsk, Khabarovsk Territory, Promyshlennaya st., building 12 Svetlogorskaya, 5

IP Belousov Evgeny Alexandrovich

Irkutsk, Irkutsk region, st. Polenova, 17

IE Bely Yu.D.

Simferopol, st. Gagarina, 14A

IP Zelenko Vladimir Vladimirovich

Ulyanovsk, Ulyanovsk region, Maksimova avenue, 30

LLC “RostKom” Tikhvinka, 37V

IP Kulakhmetova Zhuldyz Kendybaevna

Temirtau, Kazakhstan, st. Amangeldy 130

IP Ryasik Nadezhda Vyacheslavovna

DarStroy LLC

Kaluga, Kaluga region, st.

9 Reasons No Cold Water Is Coming out of Your Faucet

1. Check the Water Main or Water Supply

2. Check the Shutoff Valve

3. See If the Supply Line Is Kinked

4. Try the Spray Nozzle

5. Look for a Frozen Pipe

6. Search for Leaks

7. Investigate the Water Purifier

8. Replace the Washer

9. Check Your Faucet Cartridge Hasn’t Gone Bad

Know When to Bring in the Pros

Recommended Articles

Backed Up Sewer Could Be City’s Responsibility

Why Do I Hear Dripping in the Walls?

How Much Does Hydro Jetting Cost?

Reasons Why Your Cold Water Faucet Aren’t Working – Forbes Home

5 Reasons Why There’s No Cold Water Coming From Your Faucet

1. Cold Water Lines Exposed to Warm Environments

2. Frozen Cold Water Supply Lines

3. Closed Shut-Off Valves

4. Lime Build-Up Plugging Your Faucet

5. Failure Within the Faucet

Less Common Causes of No Cold Water From the Faucet

How to open the water supply tap if it does not open: the reasons for this situation

Content

Principle of operation

Operating tips

Ball valve does not turn, what to do

How to replace a faucet that shuts off water

Causes of breakdowns and solutions

leak

Crack in the faucet body

The valve is difficult to close or does not turn

Water runs poorly when the device is turned on

Tools for repair

Shutting off water when the tap is jammed

How to Disassemble Single Lever Ball Mixer

Main problems with ball mixer

Swivel spout not working

Clogged aerator

Problems under the sink or above

Other Possible Causes of Faults

How to fix a cartridge faucet

Gasket replacement

Crane installation

Installing a faucet if the water does not shut off

Ball valve breakdown prevention

Briefly about the main

Service center

Categories